BK Precision 1740 Instruction Manual (PDF)

The BK Precision Model 1740 manual provides detailed instructions for setting up and operating the 0-60V, 0-4A DC power supply, including guidance on using the device in constant voltage or constant current modes, and how to connect multiple units in series or parallel. It also includes troubleshooting tips, such as safety precautions to prevent electrical shock and advice on maintaining the equipment, like fuse replacement and line voltage conversion for international use.

  • Brand: BK Precision
  • Model: 1740
  • Type: manual
  • File size: 1.1 MB

Manual Overview

The B+K Precision Model 1740 DC Power Supply manual provides detailed guidance on troubleshooting, diagnostics, calibration, and board-level adjustments. The power supply offers a 0-60V DC output with a current range of 0-4A, featuring both coarse and fine controls for precise adjustments. It supports both constant voltage and constant current operations, with automatic crossover between modes. LED indicators show the current mode of operation. For troubleshooting, the manual emphasizes the importance of safety precautions due to potential high voltage hazards. It advises using a polarized 3-wire AC outlet and highlights the dangers of exposed high voltage. Calibration involves setting the voltage and current limits, which are adjustable from 5% to 100% of the maximum output. The power supply includes reverse polarity protection and overload protection to prevent damage. For board-level guidance, the manual details the use of built-in meters for continuous monitoring, and it allows for series or parallel connections for increased voltage or current output.

Quick Issues Covered

  • Diagnose power-up failures with voltage/current output checks.
  • Identify error codes for constant voltage/current mode issues.
  • Use schematics for circuit tracing and fault isolation.

Overview

The B+K Precision Model 1740 DC Power Supply is a high-quality general-purpose DC power source providing 0-60 volts DC output and 0-4 amps current output. It features adjustable coarse and fine controls for precise voltage and current settings, with two current ranges for improved settability and meter resolution. The power supply offers excellent regulation, low ripple characteristics, and includes reverse polarity protection and current limiting to prevent damage. It can operate in constant voltage or constant current modes, with automatic crossover between them. The output is isolated from chassis and earth ground, allowing flexible connections. The Model 1740 is suitable for various applications, including service shops, engineering labs, production testing, school laboratories, and home use by hobbyists.

Specifications

  • OUTPUT VOLTAGE
  • 0 to 60 VDC, coarse and fine adjustment
  • OUTPUT CURRENT
  • High Range — 0 to 4 A
  • Low Range — 0 to 1 A
  • METERING
  • Voltmeter
  • Range 0 to 64 V
  • Accuracy ±2.5%
  • Ammeter
  • Hi Range 0 to 4.4 A
  • Lo Range 0 to 1.1 A
  • Accuracy ±2.5%
  • CONSTANT VOLTAGE OPERATION
  • Voltage Regulation
  • Line (108-132) <0.2% + 2 mV
  • Load (no load to full load) <0.04% + 2 mV
  • Recovery Time ≤100 µs typical

Safety & Warnings

Normal use of test equipment exposes users to a certain amount of danger from electrical shock. Testing sometimes must be performed where exposed high voltage is present. An electrical shock causing 10 milliamps of current to pass through the heart can stop most human heartbeats. Voltage as low as 35 volts DC or AC RMS should be considered dangerous and hazardous since it can produce a lethal current under certain conditions. Higher voltages are even more dangerous. Normal work habits should include all accepted practices to prevent contact with exposed high voltage and to steer current away from the heart in case of accidental contact with high voltage.

1. There is some danger of electrical shock from the power supply output, which produces a maximum of 60 volts DC. However, there may be a great danger of electrical shock if the power supply output is connected to an external high voltage. Several possible test conditions using this power supply can create a high voltage shock hazard:
a. If the equipment under test is the “hot chassis” type, a serious shock hazard exists unless the equipment is unplugged (just turning off the equipment does not remove the hazard), or an isolation transformer is used.
b. If the equipment under test is “powered up” (and that equipment uses high voltage in any of its circuits), the power supply outputs may be floated to the potential at the point of connection. Remember that high voltage may appear at unexpected points in defective equipment. Do not float the power supply output to more than 100 volts peak with respect to chassis or earth ground.
c. If the equipment under test is “off” (and that equipment uses high voltage in any of its circuits under normal operation), discharge high-voltage capacitors before making connections or tests. Some circuits retain high voltage long after the equipment is turned off.

2. Use only a polarized 3-wire AC outlet. This assures that the power supply chassis, case, and ground terminal are connected to a good earth ground and reduces danger from electrical shock.

3. Don’t expose high voltage needlessly. Remove housings and covers only when necessary. Turn off equipment while making test connections in high-voltage circuits. Discharge high-voltage capacitors after removing power.

Download PDF (1.1 MB)

Leave a Comment