The Hallicrafters Super Skyrider manual provides detailed instructions on setting up and operating the 6-band, 12-tube superheterodyne receiver, including guidance on antenna connections and band selection for optimal performance. It also covers troubleshooting techniques such as adjusting the RF and AF gain controls, using the BFO injection for weak signals, and setting the carrier level meter for accurate signal reception.
Manual Overview
The Hallicrafters Super Skyrider models S-17 and SX-17 are six-band, 12-tube superheterodyne receivers designed for a wide range of frequency coverage. The manual emphasizes the importance of proper antenna setup to ensure optimal performance, particularly on higher frequency bands. Troubleshooting involves checking the alignment of the main dial, which should be calibrated in kilocycles for bands 1 and 2, and in megacycles for the remaining bands. Calibration accuracy is maintained when the band spread dial reads “0.”
For diagnostics, the manual suggests using the “BFO Injection” control for weak signals and adjusting the “R.F. Gain” and “A.F. Gain” controls to manage signal-to-noise ratios. The “Carrier Level” meter should be set with the “AVC” switch on and the antenna disconnected. Board-level guidance includes the use of separate coils for each band and iron-core transformers for the I.F. amplifier stages, resonating at 465 KC, which enhance gain and selectivity. The manual also details the tube lineup, including the 6K7 and 6J5 tubes, which contribute to the receiver’s performance by improving signal-to-noise ratios and providing robust audio output.
Quick Issues Covered
- Calibrate main dial with band spread dial at '0' position.
- Adjust carrier level meter with AVC switch on and RF gain open.
- Resolve power-up issues by ensuring correct 110V AC connection.
Overview
The Super Skyrider models S-17 and SX-17 are 6-band, 12-tube superheterodyne receivers. They cover frequency ranges from 545 KC to 62.00 MC, using separate coils for each band to maximize signal energy transfer. The manual provides operating instructions, including antenna setup, operation procedures, and controls for optimal reception of voice and CW signals. The receivers feature two stages of radio frequency amplification for maximum gain and selectivity, and a push-pull audio stage delivering up to 18 watts of power. The design includes a noise silencer and a high-current rectifier to support the receiver’s functions.
Specifications
- 6 band superheterodyne receiver
- Frequency coverage: 545 KC to 1,555 KC
- Frequency coverage: 1,545 KC to 4,300 KC
- Frequency coverage: 4.2 MC to 10.2 MC
- Frequency coverage: 9.8 MC to 20.5 MC
- Frequency coverage: 19.00 MC to 36.00 MC
- Frequency coverage: 35.00 MC to 62.00 MC
- Separate coils for each band
- Inductive coupling to antenna
- Main dial calibrated in kilocycles and megacycles
- Tube line-up: 6K7, 6K7, SLT, 6J5, SK7, BKT, 6R7T, 2-6VG, 6/7, 6J7, 6HG, 523
- Two stages of radio frequency amplification
- Iron-core transformers resonating at 465 KC
- Push-pull 5VG stage delivering 13 watts of audio power
- Beat oscillator 6JT
- High-current 523 rectifier
Operation
To operate the Super Skyrider models S-17 and SX-17, plug the receiver into a 110-volt AC power socket. Turn the “Tone” control to the right to power on the receiver. During warm-up, also turn the “RF Gain” and “AF Gain” knobs to the right. The receiver is initially set to the highest frequency range. Adjust the “Bands” switch until the main dial indicates the desired band. It is recommended to start with Bands No. 1 and No. 2 before attempting higher frequencies. For distant or weak signals, use the “BFO Injection” control by turning it to the right, but turn it off once the signal is located to avoid a continuous whistle. For C.W. transmissions, leave the BFO control on and adjust the “Pitch Control” knob for a pleasing beat note. When receiving voice, keep the “AVC” switch on and turn the “RF Gain” control fully to the right. If the set blocks on strong signals, manually adjust the “RF Gain” control to prevent overloading. The “Carrier Level” meter functions when the “AVC” switch is on and the “RF Gain” control is advanced to the right. For C.W. signals, turn the “AVC” switch off and use the “BFO Injection” control to adjust the beat oscillator output.