Rohde & Schwarz HZO20 Operation Manual (PDF)

The manual for the HZ020 probe covers its setup, operation, and troubleshooting, detailing specifications such as the input voltage limits, frequency response, and environmental conditions for safe use. It also provides safety instructions to prevent damage and ensure proper grounding, as well as guidelines for connecting and disconnecting the probe to measurement devices.

  • Brand: Rohde & Schwarz
  • Model: HZO20
  • Type: operation manual
  • File size: 1.7 MB

Manual Overview

The operation manual for the HZ020 probe from HAMES Instruments, a Rohde & Schwarz company, provides detailed specifications and guidelines for safe and effective use. The probe features an auto attenuation ID with a division factor of 1000:1 ±2% at DC for impulse voltages, and a system bandwidth of 400 MHz. It is designed for a maximum input voltage of 1000 V AC or DC in CAT II environments, with reduced voltage ratings at higher frequencies. The probe’s input impedance is 50 MΩ with a typical input capacitance of 7.5 pF. Calibration and adjustments should consider the compensation range of 10 pF to 50 pF. For troubleshooting, ensure proper grounding and connection to avoid exceeding the probe’s ratings. Error diagnostics involve checking the probe’s connection and ensuring it is used within specified environmental conditions, such as temperature and humidity limits. The manual emphasizes the importance of using grounded measuring devices and adhering to IEC safety standards to prevent damage and ensure accurate measurements.

Quick Issues Covered

  • Diagnose auto attenuation ID issues with HZ020 probe.
  • Troubleshoot power-up failures in grounded measurement setups.
  • Adjust compensation range for input capacitance variations.

Overview

The HZ020 is a probe from HAMES Instruments, a Rohde & Schwarz company, designed with an automatic attenuation identification feature. The manual provides specifications and safety instructions for the probe, including its electrical and mechanical properties, usage guidelines, and safety precautions. The probe is rated for a maximum input voltage of 1000 V AC or DC in CAT II conditions and has a 1000:1 division ratio. It is suitable for use in environments up to 2000 meters in altitude and within a temperature range of 0°C to 50°C during operation. The manual emphasizes the importance of proper grounding and adherence to maximum rated data to prevent damage or injury.

Specifications

  • Teilungsfaktor: 1000:1+2% bei DC für Impulsspannungen
  • Spannungskoeffizient: 0,0005 %/V [typisch]
  • System Bandbreite: 400 MHz [-3 dB]
  • Anstiegszeit: 900 ps [10 % – 90 %][typisch]
  • Maximale bemessene Eingangsspannung: 8000
  • Messkategorie: CAT II
  • Verschmutzungsgrad: 2
  • Eingangs-Widerstand: 50MO +1%
  • Eingangs-Kapazität: 7,5 pF [typisch]
  • Gewicht (nur Tastkopf): 67 g
  • Kabellänge: 2m
  • Tastkopfspitze: 5mm
  • Eingangskopplung des Messinstrumentes: 1 MQ AC / DC
  • Einsatzhöhe in Betrieb: bis zu 2000 m
  • Einsatzhöhe außer Betrieb: bis zu 15000 m
  • Temperaturbereich in Betrieb: 0° C bis +50° C
  • Temperaturbereich außer Betrieb: -40° C bis +70°C
  • Maximale relative Luftfeuchtigkeit in Betrieb: 80 % bis 30° C, linear fallend bis 40 % bei 50° C

Safety & Warnings

To avoid personal injury and damage to the product and connected devices, follow these safety precautions:

– Use only grounded measuring devices and connect the probe only to grounded measuring devices.
– Ensure that the probe and measuring device are properly grounded.
– Connect and disconnect properly: connect the probe’s connector to the measuring device and ground the lead before contacting the probe tip with the measurement point. Remove the probe tip and ground lead from the measurement point before disconnecting the probe from the measuring device.
– Do not apply a potential to the probe that exceeds its maximum rated data. Adhere to the voltage derating curve.
– Stay away from hazardous circuits and avoid working on open and unprotected circuits. Do not touch terminals or components that pose a risk of contact.
– Use only undamaged measuring accessories and have the product serviced by qualified personnel.
– Use the measuring accessory only indoors and never in damp environments or under the influence of vapors. Keep the product dry and clean.
– Do not use the product in explosive environments.
– The probe is rated for an input voltage of 1000 V AC or DC CAT II. Note that the maximum allowable input voltage decreases as the frequency of the applied signal increases.
– The probe is intended exclusively for grounded measurements. Ensure all touchable metal parts are connected to the BNC connector (GND) of the measuring device, except for the probe tip and the pin of the BNC connector.
– Be cautious when working with the thin and sharp spring contact tip to avoid injury. Avoid excessive bending or pulling of the probe cable to prevent damage.

Download PDF (1.7 MB)

Leave a Comment