The manual for the HZ040 differential probe covers setup instructions, including connecting the probe to oscilloscopes with a 50 Ω BNC input and powering it via USB or battery. It also provides operational guidance for measuring differential signals and troubleshooting tips, such as ensuring the probe is not used in wet environments and checking for mechanical damage before use.
Manual Overview
The HZ040 Differential Probe is designed for measuring high-speed differential signals in digital and power circuits, such as CAN Bus or LVDS. It supports a bandwidth of 200 MHz and features a high input resistance of 1 MΩ and low input capacitance of 3.5 pF, minimizing load on the circuit under test. The probe can be powered via USB or a 9V battery and connects to oscilloscopes with a 50 Ω BNC input. For oscilloscopes without a 50 Ω input, a 50 Ω feed-through termination like the HAMEG HZ22 is required. The probe’s differential input voltage range is +20 V, with a common mode range of +60 V. Calibration and adjustments are not specified, but users are advised to avoid exceeding voltage ratings to prevent damage. Troubleshooting involves checking for mechanical damage and ensuring proper connections. The probe should only be used by qualified personnel in dry, non-explosive environments. For repairs, users should contact HAMEG service, especially within the warranty period. Proper handling and cleaning procedures are emphasized to maintain performance and safety.
Quick Issues Covered
- Diagnose power-up failures due to incorrect voltage supply.
- Error codes for differential signal measurement issues.
- Calibration adjustments for accurate gain and bandwidth settings.
Overview
The HZ040 Differential Probe is a product designed for measuring fast differential signals, commonly found in modern digital and power circuits as well as serial bus applications like CAN. It features a 200 MHz bandwidth, high input resistance of 1 MΩ, and low input capacitance of 3.5 pF. The probe supports a wide dynamic range of +20 V differential and +60 V common mode, and can be powered via battery or USB cable. It is compatible with oscilloscopes that have a 50 Ω BNC input. The manual covers technical specifications, usage instructions, safety precautions, and maintenance guidelines.
Specifications
- 200 MHz Bandbreite
- hoher Eingangswiderstand von 1 MQ
- niedrige Eingangskapazitat von 3,5 pF
- hoher Dynamikbereich von +20 V differentiell und +60 V Gleichtakt
- universelle Stromversorgung Uber Batterie oder USB Kabel
- Teilungsfaktor: 10:1
- typ. Batterielebensdauer: 7,5 Stunden (Alkali Batterie)
- Bandbreite (-3 dB): 200 MHz
- Eigenanstiegszeit (10%-90%): 1,75 ns
- Verstarkungsgenauigkeit: +1%
- Maximale Eingangsspannung (jeder Eingang zu Masse): +40 V
- Maximale differentielle Eingangsspannung (DC + AC Spitze): +20 V
- Maximale Gleichtakt-eingangsspannung: +60 V
- Eingangswiderstand / Eingangskapazitat jeder Eingang zu Masse: 500 kO), 7 pF
- Eingangswiderstand / Eingangskapazitat zwischen den Eingangen: 1 MQ, 3,5 pF
- Ausgangsspannung: +2 V [in 50 0)
- Offset (typisch): +2 mV
- CMRR [typisch): -80 dB bei 60 Hz, -50 dB bei 10 MHz
- Spannungsversorgung: 9 V Batterie oder USB Anschluss Adapter [5 V …9 V, 200 mA]
- ungefahres Gewicht: 170g (ohne Batterie und Zubehér)
- BNC Kabellange: 120 cm
- Lange der Eingangskabel: 15 cm
- Abmasse [LxWxH]: 11x 22x 14mm
- Temperaturbereich in Betrieb: +5 °C bis +40 °C
- Temperaturbereich aufer Betrieb: -20 °C bis +70 °C
- Einsatzhohe in Betrieb: 3000 m
- Einsatzhohe aufer Betrieb: 15300 m
- Luftfeuchtigkeitsbereich: 25 – 85%
Controls & Indicators
Refer to the PDF for details.
Installation / Setup
The HZ040 differential probe can be powered via USB or a 9V battery and is compatible with oscilloscopes with a 50 Ω BNC input. For oscilloscopes without a 50 Ω input, a 50 Ω pass-through resistor like the HAMEG HZ22 is required. The probe has an input resistance of 1 MΩ and an input capacitance of 3.5 pF, ensuring minimal load on the circuit under test. It features a 10:1 division ratio. The probe should be used in clean, dry indoor environments and should not be used in explosive or damp conditions. The operating temperature range is +5°C to +40°C. The probe must be connected to grounded measuring devices, and the probe tips should be connected to the test points only after the probe is connected to the measuring device. Ensure no potential exceeding the probe’s maximum ratings is applied. The probe is intended for differential measurements between two points in a circuit and not for electrical isolation of the test object from the measuring device.
Operation
Refer to the PDF for details.
Troubleshooting & Error Codes
Refer to the PDF for details.
Safety & Warnings
– Verwenden Sie das Messzubehör nur in geschlossenen, trockenen und sauberen Räumen und nicht in feuchter oder explosiver Umgebung.
– Das Messzubehör darf nur von fachlich qualifiziertem Personal verwendet werden.
– Schließen Sie den Tastkopf nur an geerdete Messgeräte an.
– Verbinden Sie den Anschluss-Stecker des Tastkopfes zuerst mit dem Messgerät, bevor Sie die Tastkopfspitzen mit den Messpunkten kontaktieren. Entfernen Sie die Tastkopfspitzen, bevor Sie den Tastkopf vom Messgerät trennen.
– Legen Sie kein Potential an den Tastkopf an, das die maximalen Bemessungsdaten überschreitet.
– Halten Sie sich von gefährlichen Stromkreisen fern und vermeiden Sie das Arbeiten an offenen und ungeschützten Stromkreisen.
– Verwenden Sie nur einwandfreies Messzubehör und lassen Sie das Produkt nur von qualifiziertem Personal instand setzen.
– Seien Sie vorsichtig im Umgang mit scharfen Spitzen, um Verletzungen zu vermeiden, und vermeiden Sie mechanische Überlastungen des Tastkopfkabels.
– Nutzen Sie nur das mitgelieferte Zubehör, um elektrische Schläge zu vermeiden.
Download MANUAL Operation manual (PDF – 630.3 KB)
Rohde-Schwarz HZO40 Operation Manual PDF: 630.3 KB. Guides technicians in operating and troubleshooting the HZO40 model.
- Brand: Rohde-schwarz-hzo40-operation
- Model: MANUAL
- Type: Operation manual
- File size: 630.3 KB
Overview
Brief overview of the product.
Specifications
- Key spec 1
- Key spec 2
Controls & Indicators
Control panel/button layout.
Installation / Setup
- Step 1…
- Step 2…
Operation
Basic usage, modes, cycles.
Troubleshooting & Error Codes
| Issue / Code | Fix |
|---|---|
| Example | How to fix… |
Safety & Warnings
- Important warning…
Downloads
Download MANUAL operation manual (PDF)
Rohde-Schwarz HZO40 Operation Manual Overview
The Rohde-Schwarz HZO40 is a high-precision test and measurement device designed for advanced signal analysis and communication testing. It is widely used in telecommunications, aerospace, and electronic manufacturing industries to ensure accurate measurement and diagnostics of RF signals. This operation manual provides comprehensive guidance on the setup, operation, and maintenance of the HZO40 to maximize its performance and reliability.
Main Features and Specifications
- Frequency range: 9 kHz to 40 GHz
- High dynamic range with low noise floor
- Fast sweep and measurement speed for real-time analysis
- Multiple modulation analysis capabilities
- Intuitive user interface with touchscreen display
- Extensive connectivity options including USB, LAN, and GPIB
- Compact and rugged design for field and lab use
Basic Usage and Operation Tips
Before operating the HZO40, ensure the device is properly connected to a stable power source and all cables are securely attached. Power on the device and allow it to complete its self-calibration sequence. Use the touchscreen interface to select the desired measurement mode and configure parameters such as frequency range and resolution bandwidth. For accurate results, always perform a calibration with a known reference signal before conducting measurements. Utilize the built-in help menu for step-by-step guidance on specific functions.
Troubleshooting and Maintenance
If the device fails to power on, check the power cable and outlet. In case of unexpected measurement errors or signal distortion, verify all connections and perform a recalibration. Regularly clean the exterior and connectors with a soft, dry cloth to prevent dust buildup. Avoid exposure to extreme temperatures and humidity. For firmware updates and advanced diagnostics, refer to the official Rohde-Schwarz support website or contact authorized service centers.
Safety Reminder
Always follow standard electrical safety practices when operating the HZO40. Avoid opening the device enclosure to prevent exposure to high-voltage components. Use only approved accessories and cables. Ensure the device is powered off and disconnected from the power source before performing any maintenance. Proper grounding and handling precautions will help prevent damage and ensure user safety.