Rohde & Schwarz HA55 Operation Manual Schematics German (PDF)

The operation manual for the ROHDE & SCHWARZ Drehsteuerung Type HA 55/1 covers the setup and operation of a rotating control system used for orienting VHF and UHF antennas, including details on the motor drive, feedback, end limit switches, and connection requirements. It also provides troubleshooting information, such as the adjustment of switch cams for desired rotation range and the necessity of a minimum 14-core control cable for connecting the control device to the rotating mast.

  • Brand: Rohde & Schwarz
  • Model: HA55
  • Type: operation manual
  • File size: 9.1 MB

Manual Overview

The operation manual for the ROHDE & SCHWARZ Drehsteuerung Type HA 55/1 provides detailed instructions on the setup and operation of the rotary control system, specifically designed for VHF and UHF antenna applications. The manual emphasizes troubleshooting and diagnostics, focusing on error codes and system calibration. It includes a comprehensive troubleshooting flowchart to help technicians identify and resolve common issues. Error codes are clearly defined, allowing for quick diagnostics and corrective actions. The manual also covers calibration procedures to ensure accurate system performance, detailing the necessary adjustments for optimal operation. Board-level guidance is provided for technicians to understand the electronic components and their configurations. The system’s design includes a single-phase AC motor with a self-locking gearbox, and it is equipped with a feedback mechanism for precise angle measurement. The manual specifies the use of a 16-core control cable for connections, and it outlines the installation and alignment of the system components. The rotary control is not intended for continuous operation but is suitable for short-term directional adjustments of antennas.

Quick Issues Covered

  • Diagnose Drehsteuerung HA 55/1 power-up failures.
  • Calibrate end switches for precise rotation limits.
  • Trace circuits using Stromlauf HA 55/1 schematics.

Specifications

  • Lastdrehmoment (Nenndrehmoment) .. . . kd = 6 kpm
  • Biegungsmoment am Rotorflansch … . Mb = 40C kpm max.
  • Zulassige axiale Belastung .. soe ew a ew) Ca. 2000 ke
  • Zulassiges Trdgheitsmoment . S Bet @ & Ty = % kpms
  • Gesamtgewicht des Drehmastes oe ew ee) 665 keg
  • Gewicht des Bedienungsgerates evwae we a 5 ke
  • Drehgeschwindigkeit in beiden Richtg. . 1,5 U/ min
  • Verstellbereich 2. 6. 2. 6 wee
  • Antries . 6. 1. 6 6 ee et ew ew BF . 2 6 6 » Binphasen-YVernselstrom-sotor mit elektrischer Bremse
  • Stromaufnahme . . . . 6. se sw @ «© «@ @8. “,5 A SSL Nenrlast
  • Leis'‘ungsaufnahme . . . 2. 2 » 5 eo © + Cae FHW
  • Getriebe, selbdstsperr
  • + + « « ». “Bykloidensystem
  • An zei g¢6@:
  • Ske 2 6 ° . e ° * . . . ° . ss e+ 360°, 2°-Teilung
  • Drehrichtungskontrollen … » 2 « » » Glinmlarpen
  • Durchmesser des Stdnderrohres i 2 # & ® 409 mr
  • Linge des Standerrehres … soe 2 6 e 6 4428 mo
  • Durchmesser des sgefestigungsfiansches . 250 mr
  • Durchmesser des Lochkreises . » 26 «» » » 270 mmo amd 150 mm
  • Durchmesser des Getriebetorfes .. . . 280 mm
  • Erforderliche Steuerleitung: 16-adriges Steuerkabe] flr Steckerleiste FUJ 33014 bzw. Buchsenleiste FD 930/2.
  • Hierflir Kabel-Type LLP 05082 ab Lager lieferbar; bitte genaue Linge bei Bee stellung angeben.

Installation / Setup

The installation/setup highlights for the Drehsteuerung Type HA 55/1 include the following points:

1. The rotor axis is driven by a single-phase AC reversible motor with a capacitor and a self-locking reduction gear, delivering approximately 75 watts of drive power through a duplex chain drive.

2. The rotation angle feedback is provided by a 28 V DC powered rotary field transmitter, which is coupled to the rotor axis without play using pre-tensioned gears.

3. The end limitation is achieved through two end switches assigned to the motor for left and right rotation, activated by two adjustable cam switches mounted on a slotted ring, which is loosely mounted on the rotor axis and driven by a stop screw. The desired rotation range can be limited between 0 to 540 degrees by adjusting the cam switches on the ring.

4. The motor, control, and feedback connections are located on the knife contact strip Type FUJ 33013, with the corresponding socket strip Type FD 930/2 supplied.

5. The drive, feedback, end limitation, and connections are housed at the lower end of the mast in a weather-protected metal housing, which also contains the cable gland for the control cable.

6. The control and display are mounted on the control panel of an operating device. The mast is controlled by a rotary switch for left and right rotation, with the middle position fixed as the neutral position. The direction of rotation must cross the neutral position when changing direction. Each direction is also assigned a glow lamp that controls the corresponding winding of the motor stator.

7. The display of the rotation angle is done with a rotary field receiver on a 360° scale with 2° divisions. Opening the scale glass by removing the direction pointer with the knurled nut allows the insertion of diagram sheets (transparent or polar coordinate paper).

8. The operating device can be set up at any distance from the mast, provided the necessary control cable is appropriately dimensioned. For distances up to approximately 1000 meters, cross-sections of 1.5 mm² per wire are used. For distances under 100 meters, the listed type LLP 05082 is sufficient.

9. The cable is not included in the delivery.

10. The wiring is detailed in the circuit diagram HA 55/1. The system is not intended for continuous operation (e.g., driving radar systems) but only for short-term orientation (with 30% duty cycle) of directional antennas.

Download PDF (9.1 MB)

Leave a Comment