Kenwood NX-700 NX-700H Service Manual (PDF)

The Kenwood NX-700/700H service manual provides detailed instructions for system setup, installation, and operation, including pre-installation checks and planning for antenna and radio placement. It also offers troubleshooting guidance, schematic diagrams, and alignment procedures to assist technicians in servicing the VHF digital transceiver.

  • Brand: Kenwood
  • Model: NX-700
  • Type: service manual
  • File size: 4.2 MB

Manual Overview

The Kenwood NX-700/700H service manual is a comprehensive guide for technicians working with the VHF digital transceiver. It includes detailed troubleshooting procedures, error codes, and diagnostics to assist in identifying and resolving issues. The manual emphasizes the importance of following a structured troubleshooting flow to ensure efficient problem-solving. Calibration and adjustment instructions are provided to maintain optimal performance, with specific guidance on aligning transmitter frequency, deviation, and power output. Board-level guidance includes schematic diagrams and printed circuit board views to facilitate repairs and component replacements. The manual also covers pre-installation considerations, such as antenna placement and DC power wiring, to ensure proper setup and operation. Technicians are advised to adhere to safety precautions and licensing requirements, and to conduct pre-installation checks to verify the functionality of the radio and its components. The manual is intended for experienced technicians familiar with commercial-grade communication equipment.

Quick Issues Covered

  • Diagnose power-up failures with troubleshooting section on page 41.
  • Calibrate transmitter frequency and deviation using adjustment procedures on page 44.
  • Trace circuits using detailed schematic diagrams starting on page 80.

Overview

The NX-700/700H is a VHF digital transceiver manufactured by Kenwood Corporation. The service manual is intended for experienced technicians and includes comprehensive service information for the equipment. It covers topics such as system setup, realignment, installation, disassembly for repair, circuit and component descriptions, troubleshooting, and specifications. The manual also provides guidelines for pre-installation considerations, including licensing requirements and installation planning for antennas and radio placement. The product complies with the ROHS directive and uses lead-free solder.

Installation / Setup

The installation/setup highlights for the VHF Digital Transceiver NX-700/700H include several key considerations:

1. Pre-Installation Considerations:
– Unpack the radio and check for accessory items.
– Ensure compliance with licensing requirements for each radio installation.
– Perform a pre-installation checkout to verify receiver and transmitter operation.

2. Planning the Installation:
– Inspect the vehicle for suitable mounting locations for the radio antenna and accessories.
– Plan cable runs to avoid pinching or crushing wiring and ensure proper radio cooling.

3. Antenna Installation:
– The preferred antenna location is the center of a large, flat conductive area, such as the roof center or trunk lid.
– Ensure the trunk lid is bonded to the vehicle chassis using ground straps.

4. Radio Installation:
– Use the universal mount bracket to secure the radio, ensuring the mounting surface supports the radio’s weight and allows for air cooling.
– Position the radio for easy access to controls by the vehicle operator.

5. DC Power and Wiring:
– Install the radio in negative ground electrical systems only.
– Connect the positive power lead directly to the vehicle battery positive terminal and the ground lead to the battery negative terminal.
– Ensure any extended cable is sufficient for the current demand.

6. Control Station Installation:
– Select a location close to the antenna cable entry point and ensure adequate cooling for the radio and power supply.

7. Additional Notes:
– Use supplied caps to prevent dust and sand from entering unused connectors.
– The transceiver sends a status message when powered on or off if enabled.

Safety & Warnings

The following precautions are recommended for personal safety:

– Do not transmit if someone is within two feet (0.6 meters) of the antenna.
– Do not transmit until all RF connectors are secure and any open connectors are properly terminated.
– Shut off this equipment when near electrical blasting caps or while in an explosive atmosphere.
– All equipment should be properly grounded before power-up for safe operation.
– This equipment should be serviced by only qualified technicians.

Download PDF (4.2 MB)

Leave a Comment