The Heathkit manual for the Model EUW-24 Vacuum Tube Voltmeter provides detailed instructions on setting up and operating the device for measuring AC and DC voltages, as well as resistance, using a single test probe with a thumb switch for easy selection between measurement modes. It also includes troubleshooting guidance, highlighting the use of 1% multiplier resistors and a printed circuit board to ensure accurate and stable circuit operation, with all controls accessible from the front panel for user convenience.
Manual Overview
The Heathkit SCHEMATICS manual provides detailed guidance for troubleshooting, diagnostics, calibration, and board-level adjustments for the Heath Model EUW-24 Vacuum Tube Voltmeter. Troubleshooting involves checking the function and range switches, ensuring they are in the correct positions for the desired measurement. Error diagnostics are facilitated by the use of a single test probe with a thumb switch that toggles between DC and AC voltage or resistance measurements. Calibration adjustments, such as AC Balance, DC Calibrate, and AC Calibrate, are accessible through the front panel, allowing for precise tuning with a screwdriver. The manual emphasizes the importance of using the correct range settings and verifying connections at the front panel jacks for accurate readings. The printed circuit board design ensures stable operation, and the use of 1% precision resistors enhances measurement accuracy. The manual also highlights the integration of a 1.5-volt battery for resistance measurements and provides specifications for voltage ranges and input resistance.
Quick Issues Covered
- Diagnose power-up failures with neon lamp power indicator.
- Adjust AC/DC calibration via front panel access.
- Trace circuits using detailed schematic for component verification.
Overview
The Heath Model EUW-24 Vacuum Tube Voltmeter is designed for measuring AC and DC voltages and resistance. It features 1% multiplier resistors and a printed circuit board for stable circuit operation. The device includes a single test probe with a thumb switch for selecting between DC voltage and AC voltage/resistance measurements. It is suitable for use in research, design, repair, and classroom demonstrations, and is part of the Malmstadt-Enke EU-100A Instrumentation Laboratory.
Specifications
- ELECTRONIC DC VOLTMETER
- 0-1.5, 5, 15, 50, 150, 500, 1500 volts full scale.
- 11 megohms (1 megohm in probe) on all ranges.
- Balanced bridge (push-pull) using twin triode.
- Accuracy: +3% full scale.
- ELECTRONIC AC VOLTMETER
- 7 rms Ranges: 0-1.5, 5, 15, 50, 150, 500, 1500 rms scales.
- 7 Peak-to-Peak Ranges: 0-4, 14, 40, 140, 400, 1400, 4000 volts full scale.
- Frequency Response (5 V Range): +1 db 25 eps to 1 mc (600 Q source).
- Accuracy: +5% full scale.
- Input Resistance And Capacitance: 1 megohm shunted by 45 pf (measured at input terminals).
- ELECTRONIC OHMMETER
- 7 Ranges: Scale with 10 ohms center X1, X10, X100, X1000, X10K, X100K, X1MEG.
- Measures 0.1 ohms to 1000 megohms with internal battery.
- GENERAL
- 4-1/2", 200 a movement, polystyrene case.
- Meter terminals brought out to front panel to facilitate external connections.
- Combined AC-OHMS-DC switching probe, single jack input for probe and ground connections.
- Function Switch (OFF, AC, DC-, DC+, OHMS).
- Range Switch (AC and DC volts, and ohms).
- Zero Adjust.
- Ohms Adjust.
- Controls Accessible Through Front Panel: AC Balance, DC Calibrate, AC Calibrate.
- Multipliers: 1% precision type.
- Circuit Board: Printed circuit; etched metal process.
- 1 – 12AU7, twin triode meter bridge.
- 1 – 6AL5, twin diode half-wave voltage doubler.
- Power Indicator: Neon lamp.
- Battery: 1.5 volt, size C flashlight cell.
- Power Requirements: 105-125 volts, 50/60 cps AC, 10 watts.
- Cabinet Size: 6-1/2" high x 11-1/2" wide x 5" deep.
- Net Weight: 4-1/4 lbs.
- Shipping Weight: 6 lbs.
Controls & Indicators
The front-panel controls/indicators include:
– Meter terminals brought out to jacks for external connections.
– Combined AC-OHMS-DC switching probe with a single jack input for probe and ground connections.
– Function Switch with options: OFF, AC, DC-, DC+, OHMS.
– Range Switch for AC and DC volts, and ohms.
– Zero Adjust.
– Ohms Adjust.
– Controls accessible through front panel: AC Balance, DC Calibrate, AC Calibrate.
– Power Indicator: Neon lamp.