Hallicrafters SX-17 Operation Service Manual (PDF)

The Hallicrafters Super Skyrider manual provides detailed instructions for setting up, operating, and troubleshooting the 6-band, 12-tube superheterodyne receiver models S-17 and SX-17, including guidance on antenna connections and control adjustments for optimal performance. It also covers the alignment and servicing of the receiver, explaining the role of each tube and the importance of using the correct antenna for higher frequency bands to ensure maximum signal reception and clarity.

  • Brand: Hallicrafters
  • Model: SX-17
  • Type: service manual
  • File size: 1.5 MB

Manual Overview

The Hallicrafters Super Skyrider models S-17 and SX-17 are six-band, 12-tube superheterodyne receivers designed for a wide frequency range. The manual emphasizes the importance of proper antenna setup for optimal performance, especially on higher frequency bands. Troubleshooting involves ensuring correct band selection and antenna connection, with adjustments made via the “RF Gain” and “AF Gain” controls to manage signal strength and noise. Calibration is crucial, with the main dial calibrated in kilocycles and megacycles, depending on the band. The “Carrier Level” meter should be set to zero with the antenna disconnected and the receiver detuned. For error diagnostics, the manual suggests using the “BFO Injection” control to adjust the beat oscillator output for clearer reception of weak signals. The receiver’s tube lineup includes stages for RF amplification, detection, and audio amplification, with iron-core transformers resonating at 465 KC for improved signal-to-noise ratio. The manual provides detailed instructions for setting the “AVC” switch and “BFO” control based on the type of signal being received, ensuring optimal performance and minimizing interference.

Quick Issues Covered

  • Calibration accuracy depends on band spread dial reading '0'.
  • Carrier level meter adjustment requires AVC switch 'ON'.
  • Separate coils for each band; unused coils are shorted.

Overview

The Super Skyrider Models S-17 and SX-17 are six-band, 12-tube superheterodyne receivers produced by the Hallicrafters Company. These models cover a range of frequencies from 545 KC to 62.00 MC using separate coils for each band, which allows for maximum signal energy transfer. The receivers feature a main dial calibrated in kilocycles and megacycles, and they require specific antenna setups for optimal performance, especially on higher frequencies. The manual provides detailed operating instructions, including the use of various controls for tuning and reception of different types of signals, such as voice and CW transmissions. The receivers include advanced features like two stages of radio frequency amplification, a signal frequency oscillator, and a noise silencer for improved performance and signal-to-noise ratio.

Specifications

  • 6 band superheterodyne receiver
  • Frequency coverage: 545 KC to 62.00 MC
  • Separate coils for each band
  • Inductive coupling to the antenna
  • Main dial calibrated in kilocycles and megacycles
  • Tube line-up:
  • 6K7 1st stage of R.F.
  • 6K7 2nd stage of R.F.
  • 6L7 1st detector-mixer
  • 6J5 signal frequency oscillator
  • 6K7 1st I.F. amplifier
  • 6K7 2nd I.F. amplifier
  • 6R7 2nd detector, AVC, 1st stage of audio
  • 2-6V6 push-pull second stage of audio
  • 6J7 beat frequency oscillator
  • 6J7 "S" meter amplifier
  • 6H6 noise silencer
  • 5Z3 full-wave rectifier
  • Iron-core transformers resonating at 465 KC
  • Push-pull 6V6 stage delivering 13 watts of undistorted audio power
  • Beat oscillator 6J7 coupled to diode section of 6R7
  • 6J5 noise silencer in the audio end of the receiver
  • 5Z3 rectifier providing current for the receiver

Operation

To operate the Super Skyrider models S-17 and SX-17, follow these steps:

1. Plug the receiver’s power cord into a 110-volt, 60-cycle AC power socket.
2. Turn the “Tone” control to the right to power on the receiver.
3. While the receiver is warming up, turn the “RF Gain” and “AF Gain” knobs to the right.
4. The receiver is initially set to the highest frequency range. Adjust the “Bands” switch until the pointer on the calibrated main dial indicates the desired band.
5. Familiarize yourself with Bands No. 1 and No. 2 before attempting to use higher frequencies.
6. For distant or weak signals, use the “BFO Injection” control by turning the knob to the right. Once signals are located, turn it off to avoid a continuous whistle.
7. For CW transmissions, keep the “BFO Injection” control on and adjust the strength of the BFO output by turning the control to the right. Use the “Pitch Control” knob to adjust the beat note.
8. When the BFO control is on, the “AVC” switch should be in the “OFF” position.
9. For phone reception, keep the “AVC” switch in the “ON” position and turn the “RF Gain” control fully to the right until the snap switch on the rear is activated.
10. If the receiver blocks on strong signals with the “AVC” switch “OFF” and “RF Gain” wide open, manually adjust the “RF Gain” control to reduce sensitivity and prevent overloading.
11. Adjust both “RF Gain” and “AF Gain” controls to find the best signal-to-noise ratio.
12. The “Carrier Level” meter functions only when the “AVC” switch is “ON” and the “RF Gain” control is advanced to the right.
13. To set the carrier level meter, disconnect the antenna, detune the receiver from any signals, and adjust the control on the back of the chassis with the “AVC” switch “ON” and “RF Gain” wide open until the meter reads “0”.
14. For CW signal reception, keep the “AVC” switch “OFF” and the “BFO Injection” control on. Adjust the injection control for minimum output to copy weak signals. Turn the control to the right for maximum beat oscillator output.

Download PDF (1.5 MB)

Leave a Comment