The Hallicrafters SX-11 service manual provides detailed instructions for setting up and operating the 1937 Super SKYRAIDER, including connecting antennas, speakers, and adjusting various controls for optimal reception across its five frequency bands. It also offers troubleshooting tips for issues such as signal reception and interference, emphasizing the importance of proper antenna setup and control adjustments for achieving the best performance.
Manual Overview
The Hallicrafters SX-11 service manual provides detailed guidance for operating and troubleshooting this 1937 communications receiver. The SX-11 is a superheterodyne receiver covering five frequency bands from 545 KC to 38.16 MC. For optimal performance, the main dial should be calibrated with the “Band-Spread” condenser set at 200 degrees. Troubleshooting involves checking connections, especially the terminal strips for speaker and external switch connections. The receiver operates on 60 cycle, 110-volt AC, and initial setup includes adjusting the 6G5 magic eye tube and removing protective covers from the glass tubes. Calibration requires aligning the main dial with the vernier scale for accurate frequency setting. For error diagnostics, the manual suggests adjusting the “BFO INJECTION” and “PITCH CONTROL” knobs to manage signal reception and avoid continuous whistles. The “A.V.C.” switch should generally be left on for voice reception but turned off for CW signals, with sensitivity managed via the “R.F. GAIN” control. Proper antenna setup is crucial for effective operation, particularly on high-frequency bands.
Quick Issues Covered
- Diagnose power-up failures with incorrect band settings.
- Adjust RF Gain and AVC for optimal signal-to-noise ratio.
- Use schematics for circuit tracing and component verification.
Overview
The Hallicrafters SX-11 is a 1937 communications receiver known as the Super SKYRAIDER. It is a 5-band, 11-tube superheterodyne receiver that covers various frequency ranges from 545 KC to 38.16 MC. The receiver is designed to cover the American broadcast range and various amateur and shortwave bands, allowing reception of high-fidelity experimental broadcasts, aircraft, amateur, police stations, and more. The manual provides instructions on setting up and operating the receiver, including connecting speakers, antennas, and adjusting controls for optimal performance.
Specifications
- 5 bands
- 11 tubes
- Superheterodyne receiver
- Frequency range: 545 KC to 38.16 MC
- Covers American Broadcast, high-fidelity experimental broadcast, aircraft, amateur, police stations, standard frequency transmissions, short wave broadcast
- Band No. 1: 545 KC to 1230 KC
- Band No. 2: 1.28 MC to 2.85 MC
- Band No. 3: 2.75 MC to 6.82 MC
- Band No. 4: 6.75 MC to 16.40 MC
- Band No. 5: 15.40 MC to 38.16 MC
Installation / Setup
The installation/setup highlights for the Hallicrafters SX-11 Communications Receiver include the following:
1. Wiring:
– Connect the permanent magnet speaker to the terminal strip marked 5000 ohms at the lower right-hand corner on the back of the chassis.
– The terminal strip marked 500 ohms above the 5000 ohm strip can be connected to a load of that impedance.
– The terminal strip marked EXT. S# is used to turn the set on and off for standby when connected to a relay or an external switch.
2. Antenna Setup:
– The insulated antenna and doublet binding posts are located at the back left of the chassis.
– For a doublet antenna, remove the jumper from the insulated post to the chassis and connect the two wires from the doublet to the insulated posts.
– For a conventional flat-top and lead-in type of antenna, connect the lead-in to the insulated post farthest to the left, ensuring the wire jumper is connected to the chassis and the other insulated post.
– Antenna location, length, and type are crucial for successful operation, especially on high-frequency ranges.
3. Power Connection:
– Plug the receiver into a 60 cycle, 110 volt AC power socket.
4. Initial Setup:
– Remove the receiver from the shipping case, take off the dust cover, and adjust the 665 magic eye tube.
– Remove the protective paper shields over the glass tubes before replacing the dust cover.
5. Calibration:
– The main dial’s calibration will hold accurately only when the “Band-Spread” condenser is set at 200 degrees or minimum capacity position.
No specific clearances or additional prerequisites are mentioned.
Operation
The Hallicrafters SX-11 Communications Receiver operates on five frequency bands, ranging from 545 KC to 38.16 MC. To operate the receiver, remove it from the shipping case, adjust the 6G5 magic eye tube, and connect the necessary components such as the speaker and antenna. The receiver is powered by plugging it into a 60 cycle, 110-volt AC power socket. The “Tone” control connects the receiver to the AC line, and the “RF Gain” and “AVC Gain” knobs should be turned to the right during warm-up. The band-change switch is initially set to the highest frequency range, and the desired band can be selected using the “Bands” switch. The “BAND SET” knob is used to tune to the desired frequency. For weak or distant stations, the “BFO INJECTION” control can be used, and the “PITCH CONTROL” helps adjust the beat note. The “A.V.C.” switch should be “ON” for receiving voice signals, and the “RF GAIN” control should be adjusted accordingly. For CW signals, the “A.V.C.” switch should be “OFF” and the “BFO INJECTION” control turned on. The crystal circuit requires the “BFO INJECTION” control to be “OFF” for proper adjustment.