The Hallicrafters Model S-72 manual provides detailed instructions for setting up and operating the portable all-wave superheterodyne radio receiver, including guidance on using built-in and external antennas for optimal reception on both standard broadcast and shortwave bands. It also offers troubleshooting tips for battery and AC/DC operation, emphasizing the importance of careful sensitivity and tuning adjustments to minimize noise and ensure high-quality signal reception.
Manual Overview
The Hallicrafters Model S-72 is a portable superheterodyne radio receiver designed for both standard broadcast and shortwave bands, covering frequencies from 540 kilocycles to 80 megacycles. It features eight tubes and a selenium rectifier, with built-in loop and whip antennas for different reception conditions. The troubleshooting section emphasizes careful adjustment of sensitivity and tuning controls to minimize noise and enhance weak signal reception. For error diagnostics, the manual suggests checking power source compatibility and ensuring proper antenna setup. Calibration involves using the BAND SPREAD control for fine-tuning shortwave frequencies, with the TUNING dial set correctly for accurate frequency logging. Board-level guidance includes ensuring correct tube and rectifier function. Battery operation requires specific installation steps to avoid damage from leakage, while AC/DC operation involves verifying power source specifications. The manual provides detailed instructions for both standard and shortwave reception, emphasizing the importance of correct antenna and control settings for optimal performance.
Quick Issues Covered
- Diagnose power-up failures with AC/DC power source guidance.
- Adjust BAND SPREAD for fine tuning shortwave frequencies.
- Calibrate TUNING dial with BAND SPREAD set at zero.
Overview
The Hallicra Model $72 is a portable all-wave superheterodyne radio receiver that covers standard broadcast and both foreign and domestic shortwave bands. It supports AM and CW reception across a frequency range from 540 kilocycles to 80 megacycles. The receiver includes eight tubes, a selenium rectifier, built-in antenna facilities, and a 5-inch PM speaker. It can operate from a 105-125 volt DC or 50-60 cycle AC power source, as well as a self-contained 90 volt – 74 volt battery pack for portable use. The manual emphasizes the importance of following installation and operation instructions to ensure optimal performance and minimize noise.
Specifications
- Model $72
- Portable all-wave superheterodyne radio receiver
- Covers standard broadcast and shortwave bands
- AM and CW reception
- Frequency range: 540 kilocycles to 80 megacycles
- 8 tubes and a selenium rectifier
- Built-in loop antenna for band 1
- Telescoping whip antenna for bands 2, 3, and 4
- External single wire antenna terminal
- BAND SPREAD control for fine tuning
- Built-in 5 inch PM speaker
- PHONES jack for headphones
- VOICE/CODE control for AM and CW selection
- RF gain or sensitivity adjustment
- Operates on 105-125 volt DC or 50-60 cycle AC power
- Portable operation with 90 volt – 74 volt battery pack
- Power consumption: 25 watts
- Headphone output impedance: 100 ohms
- Voice coil impedance: 3 ohms
Controls & Indicators
The source does not provide specific information about the front-panel controls/indicators.
Installation / Setup
The installation/setup highlights for the Hallicrafter Model $72 radio receiver include:
1. Unpacking: Check all shipping labels and tags for instructions before removing or destroying them.
2. Location: The receiver can be used portably or mounted on a table or shelf. For shortwave reception, ensure clearance for the 61-inch whip antenna, which must be fully extended for optimal performance.
3. Battery Operation:
– Select a 90 volt – 74 volt battery pack.
– Open the rear door of the cabinet, place the battery pack in the compartment, and secure it with the battery strap.
– Insert the battery cable plug into the battery receptacle and the line cord plug into the chassis receptacle.
– Do not store the receiver with the battery in the compartment to avoid damage from potential leakage.
4. AC/DC Operation:
– The receiver operates on a 105-125 volt DC or 50-60 cycle AC power source with a power consumption of 25 watts.
– Insert the line cord plug into a power outlet.
– For DC operation, reverse the line cord plug if the receiver does not operate after being turned on.
– For 220 volt, 50-60 cycle AC sources, use a special step-down transformer available as an accessory.
5. Antenna: Built-in loop antenna for standard broadcast reception and a telescoping whip antenna for shortwave reception. An external single wire antenna can be connected in areas with low signal strength.
Operation
BATTERY OPERATION
1. Select a suitable 90 volt – 74 volt battery pack.
2. Open the rear door of the cabinet using the finger grip.
3. Place the battery pack into the compartment below the receiver chassis and secure it with the BATTERY STRAP.
4. Insert the BATTERY CABLE PLUG into the BATTERY RECEPTACLE.
5. Insert the LINE CORD PLUG into the CHASSIS RECEPTACLE.
Note: Remove the battery when storing the receiver to prevent damage from leakage.
AC/DC OPERATION
1. The receiver can operate from a 105-125 volt, DC or 50-60 cycle AC power source.
2. Plug the line cord into a power outlet.
3. For DC operation, reverse the line cord plug if the receiver does not turn on.
4. A step-down transformer is needed for operation from a 220 volt, 50-60 cycle AC source.
STANDARD BROADCAST RECEPTION
1. Set the BAND SELECTOR switch to 1.
2. Turn the VOICE/CODE control to the VOICE position.
3. Set the BAND SPREAD dial to 0.
4. Adjust the ON-OFF VOLUME control for volume.
5. Tune the desired station using the TUNING control.
6. Rotate the receiver for optimal signal reception.
7. Turn off the receiver by turning the ON-OFF VOLUME control counterclockwise.
SHORTWAVE RECEPTION
1. Extend the whip antenna fully.
2. Set the BAND SELECTOR switch to 2, 3, or 4.
3. Set the BAND SPREAD dial pointer to 0.
4. For VOICE RECEPTION, turn the VOICE/CODE control to VOICE. For CODE RECEPTION, set it to CODE.
5. Adjust the ON-OFF VOLUME control for volume.
6. Tune the desired station using the TUNING control. For CODE RECEPTION, adjust for desired pitch.
7. Use BAND SPREAD TUNING for fine tuning.
BAND SPREAD TUNING
1. Use the BAND SPREAD control for fine tuning.
2. Set the BAND SPREAD dial pointer to 0.
3. Set the TUNING DIAL pointer at the high frequency end.
4. Tune through the frequency range with the BAND SPREAD control.
5. Record settings for logging shortwave stations.
HEADPHONES
1. Use headphones with an impedance of 500 to 2000 ohms.
2. Insert the headphone plug into the PHONES jack to disconnect the speaker.
3. Store headphones in the rear door compartment.
Safety & Warnings
The manual does not contain any specific safety warnings or precautions.