Hallicrafters S-19R Operation Service Manual (PDF)

The Hallicrafters Sky Buddy Model S-19R manual provides detailed instructions for setting up and operating the 6-tube, 4-band superheterodyne receiver, including recommendations for antenna configurations and control operations to optimize performance across various frequency bands. It also includes alignment and troubleshooting procedures, such as adjusting trimmers and padders for maximum output and checking components like the BFO circuit and tubes to ensure proper functionality.

  • Brand: Hallicrafters
  • Model: S-19R
  • Type: service manual
  • File size: 91.4 KB

Manual Overview

The Hallicrafters Sky Buddy Model S-19R is a 6-tube, 4-band superheterodyne receiver. It covers frequencies from 640 KC to 46.0 MC across its bands. For optimal performance, an inverted “L” antenna or a half-wave doublet antenna is recommended, with specific guidance on antenna length calculation provided. The receiver features controls for tuning, band selection, and optional use of a Beat Frequency Oscillator (BFO) for code signal reception. Troubleshooting involves checking the BFO circuit, including the .0006 condenser and the 76 BFO tube if issues arise. Alignment procedures include setting the audio gain to maximum, using a signal generator at 458 KC for IF alignment, and adjusting trimmers on transformers T1 and T2. RF alignment requires connecting a generator to the A1 terminal and adjusting trimmers and padders for each band. The manual also provides a parts list for capacitors and resistors, essential for board-level servicing.

Quick Issues Covered

  • Diagnose BFO issues; check 76 BFO tube and .0006 capacitor.
  • Calibrate IF alignment using 458 KC signal generator.
  • RF alignment requires tuning adjustments for optimal reception.

Overview

The Sky Buddy Receiver Model S-I9R is a 6-tube, 4-band superheterodyne receiver produced by the Hallicrafters Co. It covers frequencies from 640 KC to 46.0 MC across its four bands. The manual provides operating instructions, including details on antenna setup for optimal performance, control operations, and alignment procedures. The receiver features controls for tuning, band selection, and optional use of a Beat Frequency Oscillator. It includes a tube lineup and power specifications, drawing 50 watts at 117 volts, 60 cycles A.C. The manual also outlines alignment procedures for both I.F. and R.F. adjustments.

Specifications

  • 6 tube
  • 4 band superheterodyne receiver
  • Frequencies: Band 1 = 640 KC to 1700 KC, Band 2 = 1.7 MC to 5.5 MC, Band 3 = 5.5 MC to 17.0 MC, Band 4 = 16.0 MC to 46.0 MC
  • Tube lineup: 6K8G, 6SK7, 6SQ7GT, 41, 76, 80
  • Power: 50 watts at 117 volts, 60 cycles A.C.

Controls & Indicators

The model S-19R Sky Buddy is equipped with the following front-panel controls and indicators:

1. Main Tuning Control: Rotates the large calibrated dial to locate the desired frequency. Calibration is accurate when the “Bandspread” dial is set at “0” or minimum capacity.

2. Bandspread Control: Provides smooth and satisfactory electrical bandspread action, driven by a gearless mechanism.

3. Send-Receive Switch: Removes plate voltage from the tubes when in the “send” position.

4. Band Switch: Allows selection of any one of the four frequency ranges covered by the receiver.

5. B.F.O. On-Off Switch: Optional use of the Beat Frequency Oscillator for copying code signals and locating weak signals.

6. Pitch Control Knob: Varies the pitch of the beat note when the BFO switch is on, aiding in copying through interference.

7. A.V.C. On-Off Switch: Optional use of automatic volume control. For strong signals, the A.V.C. switch should be “on”. For maximum sensitivity, leave it “off” and manually adjust the gain.

8. Volume Control: Turns the receiver on and off and adjusts the volume delivered by the receiver.

9. Headphone Jack: Mounted on the panel to the right of the Pitch Control Knob. Inserting the headphone plug disconnects the speaker automatically.

Operation

The Sky Buddy Model S-19R is a 6-tube, 4-band superheterodyne receiver covering specific frequency ranges. For optimal operation, an inverted “L” type antenna or a half-wave doublet antenna can be used. The receiver includes controls such as a tuning dial, bandspread, send-receive switch, band switch, B.F.O. switch, pitch control, and A.V.C. switch. The receiver is powered on and off with a volume control, and a headphone jack is available. The tube lineup includes 6K8G, 6SK7, 6SQ7GT, 41, 76, and 80. The receiver operates on 50 watts at 117 volts, 60 cycles A.C.

Download PDF (91.4 KB)

Leave a Comment