The Hallicrafters service manual provides detailed instructions for setting up and operating the Radio Receiver R-96A/SR, including its installation in a standard 19-inch rack for shore stations and maintaining the outer case for shipboard use. It also covers troubleshooting tips, such as ensuring antenna leads are well shielded and using the automatic noise limiter circuit to assist with reception during pulse-type noise interference.
Manual Overview
The Hallicrafters 2 service manual provides detailed instructions for troubleshooting, diagnostics, calibration, and board-level adjustments of the Radio Receiver R-96A/SR. The manual emphasizes the importance of maintaining proper shielding of antenna leads to prevent interference and ensure compliance with FCC regulations. Troubleshooting involves checking connections and components such as tubes, fuses, and pilot lamps, with spare parts provided for these expendable items. The receiver features an automatic noise limiter to enhance signal reception amidst pulse noise interference. Calibration involves ensuring the receiver operates within specified frequency ranges, from 135 to 510 ke and 1 to 12 me, with four crystal-controlled channels available. For diagnostics, the manual highlights the use of a send-receive switch for antenna relay operation. Board-level guidance includes accessing internal components by removing the rear access plate and ensuring proper power input connections. The receiver is designed for both shipboard and shore station use, with specific instructions for mounting and operation in different environments.
Quick Issues Covered
- Diagnose power-up failures with 115V AC/DC input issues.
- Calibrate frequency range from 135-510 ke and 1-12 me.
- Trace circuits using detailed R-96A/SR schematics.
Overview
The product is the Radio Receiver R-96A/SR, an 11-tube superheterodyne receiver designed to receive amplitude-modulated (a-m) and continuous wave (c-w) signals in the frequency ranges of 135 to 510 kilocycles (ke) and 1 to 12 megacycles (me). It covers the operating frequencies of standard marine bands and many land-based and airborne transmitters. The receiver includes four crystal-controlled channels in the 1,700 to 8,700 ke frequency range. It features a built-in speaker, a phone jack for headset operation, and an automatic noise limiter circuit to assist in reception during pulse-type noise interference. The receiver is suitable for desk or shelf mounting and can support the weight of Radio Transmitter T-83/SR when used together. The manual covers technical characteristics, packaging, and installation instructions, as well as spare parts and additional equipment requirements.
Specifications
- Frequency range:
- Band 1: 185 to 260 ke
- Band 2: 260 to 510 ke
- Band 3: 1.0 to 3.0 me
- Band 4: 3.0 to 6.0 me
- Band 5: 6.0 to 12.0 me
- Crystal-controlled channels: Four in the frequency range of 1,700 ke to 8,700 ke
- Crystal type: Crystal Unit CR-18/U
- Receiver type: Superheterodyne
- Types of signals which can be received: C-w, tone, and am voice
- Number of tubes: 11
- Intermediate frequency (IF): 550 ke
- Power input: 115-volt, 50- to 60-cycle ac, 100 watts; 115-volt dc, 100 watts
- Antenna: Single wire
- Weight: 69.5 pounds
Controls & Indicators
All operating controls are located on the front panel.
Installation / Setup
The setup highlights for the Radio Receiver R-96A/SR include the following points:
– The receiver is packed in a nailed wooden shipping container with spare parts in a metal container.
– All loose wires and cables are secured before packaging.
– The receiver can be mounted on a standard 19-inch rack panel when operated in shore stations.
– The antenna leads between the relay and the receiver input terminals should be well shielded.
– The receiver is designed to support the weight of Radio Transmitter T-83/SR when used together.
– Access to fuses, antenna and terminal strip connections, and power input connection is made by removing the rear access plate.
– A special connecting cable is required when the receiver is used with Radio Transmitter T-83/SR.
– The receiver should not be removed from its cabinet on shipboard as it changes the radiation characteristics.