The manual for the Drake DDS VFO covers the setup, operation, and troubleshooting of the digital VFO, including details on display functions, key descriptions, and programming parameters for oscillator setup. It provides instructions for tuning, memory storage, and scanning functions, as well as guidance on setting IF frequency values for both RX and TX, and addresses potential issues like low-intensity spurs in specific frequency bands.
Manual Overview
The Drake DDS-VFO manual provides detailed instructions for operating and troubleshooting the digital VFO system. It includes descriptions of display functions, key operations, and memory management. The display shows current frequency, VFO selection, and band information. Key functions include switching VFOs, activating split operation, and adjusting received frequency. The manual outlines how to store and recall frequencies in memory and perform band scans. For calibration, users can program IF frequency values for both RX and TX, ensuring accurate tuning. The manual also details how to set up the VFO as a signal generator by adjusting the IF value to zero. Troubleshooting guidance includes checking the VFO band indication and adjusting the band switch for optimal performance. The manual provides board-level guidance for oscillator setup, detailing how to program oscillator frequency and PLL multiplier values. Error codes and diagnostics are not explicitly detailed, but the manual emphasizes the importance of correct setup and calibration for optimal functionality.
Quick Issues Covered
- Diagnose power-up failures with default parameter checks.
- Adjust IF frequency for RX/TX calibration and zero beat.
- Resolve low intensity spurs in the 28 MHz band.
Specifications
- DISPLAY & FUNCTIONS
- VFO Switches between VFO A and VFO B
- SPL Pressing this switch it selects “split operation”
- RIT Pressing this switch it activates the RIT operation
- BAND This key has three functions: BAND – STEP – TUNING
- LOCK This switch locks the main tuning knob
- TX TIME When PTT is depressed the display shows the time run during transmission
- MEM WRITE: The current tuned frequency (VFOA or VFOB) is stored in the selected memory position
- MEM READ: Recall a frequency from memory
- SCANA–>B: The scan runs from VFO A to VFO B
- SCAN MEM: The scan runs selecting memories
- VFOA=B: Pressing this switch it copies the frequency of VFO B to VFO A
- VFOB=A: Pressing this switch it copies the frequency of VFO A to VFO B
- SWL BAND: Pressing KEY “+” or KEY “-“ it moves up / down on SWL BANDS
- DDS Level : the DDS output level can be programmed from +8 dBm to — inf.
- USING Digital VFO
- The DDS digital VFO gives you the full control of your receiver and transmitter
- The IF frequency value can be programmed
- It is possible to setup different IF offsets for RX and TX
- To change the IF RX frequency value, simply tune the frequency required
- To change the IF TX frequency value, simply tune the frequency required
- If a different voltage is present on the MUTE contact an opto-coupler is necessary
- When turning ON the VFO, this will tune to the same frequency previously set
- When you are tuning with fast steps, control the VFO band indication on the display
- In the Drake DDS version it has been tested that some very low intensity spurs are received only In the 28 MHz band
- There are some default set-up at start-up
- STEP 50 Hz
- TX TIME OFF
- RIT OFF
- SPLIT OFF
- LOCK OFF
- Start-up programming:
- There are some parameters that can be programmed into the DDS VFO
- OSCILLATOR SET_UP:
- Switch “ON” the controller with KEY “VFO” pressed till “Oscillator Set-up” is shown on the display
- Press Key “+” or Key — to change the values of oscillator frequency
- Some oscillator values are reported in the following table:
- External Oscillator Freq. Programmed parameter: Internal DDS
- 20 MHz 116 ( PLL multiplier = 20)
- 40 MHz 84 (PLL multiplier =10)
- 50 MHz 68 ( PLL multiplier = 8)
- 80 MHz 44 ( PLL multiplier = 5)
- 100 MHz 36 ( PLL multiplier = 4)
- 100 MHz O (PLL bypassed)
- 133 MHz O (PLL bypassed)
- 400 MHz O (PLL bypassed)
- 500 MHz * O (PLL bypassed)
Operation
The DDS digital VFO allows full control of a receiver and transmitter, similar to modern commercial transceivers. It includes features such as VFO switching, split operation, RIT operation, band selection, tuning step adjustment, and memory functions. The VFO can be used as a signal generator or for direct conversion receivers by setting the IF value to 0. It supports programming different IF offsets for RX and TX, useful for homebrew transceivers. The VFO retains the last set frequency on power-up and requires band switching and preselector adjustment for correct operation. Default settings include a 50 Hz step, TX time off, RIT off, split off, and lock off. The oscillator setup can be programmed by switching on the controller with specific keys pressed, allowing changes to oscillator frequency and PLL multiplier.