BK Precision 810C Instruction Manual (PDF)

The BK Precision Capacitance Meter manual provides instructions for setup, operation, and troubleshooting, including details on measuring capacitance, battery replacement, and fuse replacement. It emphasizes safety precautions such as discharging capacitors before measurement and provides technical specifications and warranty information.

  • Brand: BK Precision
  • Model: 810C
  • Type: manual
  • File size: 92.5 KB

Manual Overview

The BK Precision 810C Capacitance Meter manual provides detailed instructions for troubleshooting, diagnostics, calibration, and maintenance. The meter features a 3½ digit LCD with automatic polarity and overrange indication. For troubleshooting, the manual advises checking the fuse if no measurements are possible, as the device is protected by a 0.1A/250V fast-acting fuse. Calibration involves using the “0-ADJ” knob to subtract stray capacitance for measurements under 200nF. The meter operates with a single 9-volt battery, and a low battery is indicated by “E=1” on the display. Battery replacement requires removing two screws to access the battery compartment. The device should not be exposed to external voltage to prevent damage, and capacitors must be discharged before measurement. The manual also includes guidance on replacing the fuse and emphasizes the importance of using the original type. The meter’s accuracy is specified at 23°C with less than 75% relative humidity.

Quick Issues Covered

  • Low battery indication triggers 'E=1' on display.
  • Check fuse if capacitance measurements fail.
  • Zero adjust knob compensates for stray capacitance.

Overview

BK Precision 810C is a capacitance meter featuring a 3.5-digit LCD display with a maximum reading of 1999. It automatically indicates polarity and has an overrange display. The device includes automatic zero adjustment and low battery indication. It operates in environments from 0°C to 40°C with less than 70% relative humidity and is powered by a 9-volt battery. The capacitance meter comes with test leads, a 9V battery, a spare fuse, and operating instructions. The manual covers specifications, operation instructions, battery and fuse replacement, and warranty information.

Specifications

  • Display: 3 1/2 digit liquid crystal display (LCD) with a maximum reading of 1999
  • Polarity: Automatic, positive implied, negative polarity indication
  • Overrange: (1) or (-1) is displayed
  • Zero: Automatic
  • Low battery indication: The "E=1" is displayed when the battery voltage drops below the operating level
  • Measurement rate: 2 times per second, nominal
  • Operating Environment: 0°C to 40°C at < 70% relative humidity
  • Storage Temperature: -20°C to 60°C, 0 to 80% R.H. with battery removed from meter
  • Accuracy: Stated accuracy at 23°C ± 5°C, <75% relative humidity
  • Power: single standard 9-volt battery, NEDA 1604, JIS 006P, IEC 6F22
  • Battery life: 300 hours typical with carbon-zinc
  • Dimensions: 151mm (H) x 70mm (W) x 38mm (D)
  • Weight: Approx. 7 oz. (200g) including battery
  • Accessories: One pair test leads, 9V battery (installed), one spare fuse (installed) and Operating Instructions
  • Test voltage: <3.5V
  • Input protection: 0.1A/250V fast acting fuse
  • Zero adjust limited: +20pF approx.

Operation

To use the BK Precision 810C Capacitance Meter, follow these steps:

1. Discharge the capacitor before measuring to avoid electrical hazards.
2. Set the range switch to the desired range.
3. Never apply an external voltage to the input terminals to prevent damage to the meter.
4. Observe polarity when measuring polarized capacitors.
5. Insert the capacitor leads into the receptacle socket or directly connect the test clip to the capacitor leads as required.
6. Read the capacitance directly from the display.

Safety & Warnings

To avoid electrical hazards, discharge the capacitor before measuring. Never apply an external voltage to the input terminals as damage to the meter may result. Observe polarity when measuring polarized capacitors.

Download PDF (92.5 KB)

Leave a Comment