The manual for the B&K Model 3050 Audio Sine/Square Wave Generator provides detailed instructions on setup, operation, and troubleshooting, including how to adjust output voltage, select frequency, and synchronize with external signals. It also includes specifications such as output impedance, power requirements, and operating temperature, along with a description of the front and rear panel controls.
Manual Overview
The B&K Model 3050 Audio Sine/Square Wave Generator manual provides detailed guidance for technicians on operating and troubleshooting the device. The manual emphasizes the importance of understanding the troubleshooting flow, which involves checking power connections and ensuring the neon lamp indicator is lit when the power switch is on. Error codes and diagnostics are not explicitly detailed, but calibration and adjustments are crucial, particularly in setting the desired frequency using the frequency dial and range selector switch. The output voltage can be adjusted with the OUTPUT LEVEL control, and the attenuator settings allow for precise voltage regulation. For synchronization, the manual describes connecting an external signal to the SYNC INPUT terminal, enabling frequency synchronization within a specified range. Board-level guidance is not explicitly covered, but the manual provides comprehensive instructions on using the front and rear panel controls to achieve desired output characteristics. The manual also includes examples of applications, such as measuring amplifier characteristics using sine wave signals.
Quick Issues Covered
- Diagnose power-up failures with neon lamp indicator.
- Calibrate frequency using FREQ RANGE and FREQUENCY dial.
- Trace circuit issues using detailed schematic diagrams.
Specifications
- Output Impedance: Approx. 600 ohms
- Output Attenuator: 0dB, 20dB, 40dB (3 steps)
- Output Vernier: Continuously variable output adjustment
- Synchronizing Range: Approx. 1% per volt or more
- Max. Input Voltage: 10V RMS
- Input Impedance: Approx. 20,000 ohms
- Frequency Drift: Less than ±0.5%
- Output Level Variation: Less than ±0.5dB
- Operating Temperature: 0-50°C at relative humidity of 90% or less
- Power Requirements: 117V AC, 50/60Hz (can be converted to 230V and 100V, 50/60Hz operation)
- Power Consumption: Approx. 7 watts
- Dimensions: 7-3/4" W x 9-5/8" D x 6" H
- Accessories Included: One red test cord with basket clip and banana plug, One black test cord with basket clip and banana plug, One 0.1 A fuse, One copy of instruction manual
Controls & Indicators
The front-panel controls and indicators for the Model 3050 Audio Sine/Square Wave Generator include:
1. Neon Lamp: Lights up when the power switch is turned on.
2. Power: Slide switch to turn the unit on and off.
3. Output Attenuator (dB): Allows signal delivery to the output terminal with options for 0dB, 20dB, or 40dB attenuation.
4. Grounding Terminal: Labeled as GND.
5. Output Terminal: Approximately 600 ohms impedance.
6. Waveform Selector: Allows selection between sine wave and square wave output.
7. Frequency Range Selector: Serves as a multiplier for frequency setting with options X1, X10, X100, and X1000.
8. Output Level: Used to continuously vary output voltage from 0-10 volts RMS.
9. Frequency: Vernier frequency adjustment dial.
10. Scale Plate: Dial scale with graduations of 20-200.
11. Pointer: Indicates frequency setting.
Operation
The operation of the Model 3050 Audio Sine/Square Wave Generator involves several basic steps:
1. Turning the Unit On: Connect the power cord to a power source and turn the power switch to ON. The neon lamp will light up, indicating the unit is on. Allow 3 minutes for warm-up stabilization.
2. Selection of Desired Frequency: Use the FREQUENCY dial with the FREQ RANGE selector switch set at the appropriate position. Adjust until the pointer is set to the desired frequency setting on the dial scale. The frequency is determined by multiplying the dial scale reading by the frequency range factor.
3. Adjustment of Output Voltage: The output voltage can be adjusted using the OUTPUT LEVEL control to any desired voltage within a range of 0 to 10V RMS. The OUTPUT ATT switch can be used to attenuate the signal by 20dB or 40dB.
4. Use of Synchronizing Input Terminal: Connect an external synchronizing signal to the SYNC INPUT terminal to synchronize the oscillating frequency with the external signal. The synchronization range is approximately 1% per volt of the synchronizing signal.
These steps allow the user to operate the Model 3050 effectively for generating sine and square wave signals.