The manual for the B&K Precision Model 3003 handheld signal generator provides detailed instructions on setting up and operating the device, including selecting the desired frequency using push wheel switches and adjusting the amplitude of the output. It also includes troubleshooting guidelines, safety precautions, and information on warranty and repair services.
Manual Overview
The B&K Precision Model 3003 is a 10 MHz handheld signal generator designed for generating sine and square waveforms with a frequency range from DC to 9.9999999 MHz and an accuracy of 0.02%. The device features eight push wheel switches for frequency selection and variable amplitude control for sine waves. The output impedance for both waveform types is 50 ohms, and the device can be powered by an external AC adapter or a 9V battery. Troubleshooting involves ensuring correct frequency and amplitude settings, checking power sources, and verifying connections. Error diagnostics are not specified, but users should avoid connecting the output to signal injection points to prevent damage. Calibration adjustments are made using the output level control. For board-level guidance, users should familiarize themselves with the equipment under test, especially high voltage points, and follow safety precautions to avoid electrical shock. Warranty service requires returning the product with proof of purchase, while non-warranty service involves pre-paid shipping and payment for repairs.
Quick Issues Covered
- Diagnose power-up failures with AC adapter or 9V battery.
- Adjust sine wave amplitude using output level control.
- Identify low battery with 'Bat Low' indicator.
Overview
The Model 3003 is a 10 MHz handheld signal generator designed as a cost-effective signal source. It utilizes direct-digital synthesizer technology for clean and accurate waveforms, offering sine and square wave outputs with frequency accuracy of 0.02% and 0.1 Hz frequency resolution. The device features user-friendly controls, including eight push wheel switches for frequency setting, variable amplitude control for sine waves, and standard BNC connectors. It can be powered by an external AC adapter or a 9V battery and includes a low battery indicator. The manual covers operation instructions, safety guidelines, warranty information, and service procedures.
Specifications
- Model 3003
- 10 MHz HANDHELD SIGNAL GENERATOR
- Waveforms: Sine, Square
- Frequency Range: DC to 9.9999999MHz
- Frequency Accuracy: 0.02%
- Frequency Resolution: 0.1Hz
- Sine Wave Output: 0 – 4.5Vp-p (no load)
- Variable amplitude control
- Output impedance: 50 ohms
- Square Wave Output: 5Vp-p (no load)
- Duty Cycle: 50% typical
- Output impedance: 50 ohms
- Power: An external AC adapter (6V – 9V DC, 150mA, 5.5mm x 2.1mm center pin+) or one 9V battery
- Dimensions: 2.1" x 3.6" x 6.0"
- Power Switch: Power on or off
- Power indicator: LED to show when power is on
- Frequency indicator: The eight push wheel switches indicate the frequency that output on the sine and square waves jacks
- Output level control: Controls the amplitude of the sine wave at output jack
- Sine connector: Sine wave output at this jack
- Square connector: Square wave output at this jack
- Bat Low: Indicates battery condition
- AC Adapter Jack: (6.5V – 9V) DC, 150mA center pin + adapter input
Controls & Indicators
The Model 3003 handheld signal generator has the following front-panel controls and indicators:
– Power Switch: Used to turn the unit on or off.
– Power Indicator: An LED that shows when the power is on.
– Frequency Indicator: Eight push wheel switches that indicate the frequency output on the sine and square waves jacks.
– Output Level Control: Controls the amplitude of the sine wave at the output jack.
– Sine Connector: The output jack for the sine wave.
– Square Connector: The output jack for the square wave.
– Bat Low Indicator: Indicates the battery condition.
– AC Adapter Jack: Input for a 6.5V to 9V DC, 150mA center pin positive adapter.
Operation
To operate the Model 3003 handheld signal generator, follow these steps:
1. Turn on the unit and select the desired frequency of the waveform using the eight push wheel switches.
2. Adjust the amplitude of the output as needed with the output level control, which affects only the sine wave output jack.
3. Connect the generator output to the desired test points.
Caution: The signal generator output should not be connected to a signal injection point, as excessive voltage at the point of signal injection can cause internal damage.
Safety & Warnings
The safety warnings and precautions explicitly present in the manual are as follows:
1. An electrical current of over 10 milliamps passing through the heart can stop most human hearts. Voltage as low as 35 volts DC or AC RMS should be considered hazardous since it can produce lethal current under certain conditions.
2. There are no high voltages in the signal generator, but the equipment under test usually contains hazardous high voltage. Always follow the safety recommendations of the manufacturer of your equipment.
3. Some equipment may be wired as a “hot chassis” type; equipment using two-wire power plugs are always suspect and it may even include those with polarized plugs. Never touch the chassis of “hot chassis” type equipment to avoid the possibility of a serious, possibly fatal electrical shock.
4. Don’t expose yourself needlessly to high voltage; only remove housings and covers when necessary.
5. Familiarize yourself with the equipment being tested and the location of its high voltage points. However, be aware that high voltage may appear at unexpected points in defective equipment.
6. Never work alone. Someone should be nearby to render aid if needed. Training in CPR (Cardio-pulmonary resuscitation) is highly recommended.