BK Precision 231A Instruction Manual (PDF)

The BK Precision 231A Multi-Network Cable Tester manual provides instructions for setting up and operating the device, including testing various cable types such as 10BASE-T, 10BASE-2, RJ45/RJ11, and Token Ring cables, and offers guidance on using the remote terminator for testing installed cables. It also covers troubleshooting procedures for identifying faults like open, shorted, and crossed pairs, and includes a warranty section for service and repair information.

  • Brand: BK Precision
  • Model: 231A
  • Type: manual
  • File size: 194.2 KB

Manual Overview

The BK Precision 231A Multi-Network Cable Tester manual provides detailed instructions for troubleshooting, error diagnostics, and calibration of various cable types, including 10BASE-T, 10BASE-2, RJ45/RJ11, and Token Ring cables. The tester identifies pin configurations and faults such as open, shorted, and crossed pairs. For troubleshooting, the manual emphasizes the importance of ensuring sufficient battery power to avoid dimmed LEDs and incorrect results. The device offers both auto and manual scanning modes, allowing users to switch modes to suit their testing needs. Error diagnostics are facilitated through LED displays that indicate continuity, open wires, shorts, and miswires. Calibration involves ensuring proper connections and using the manual mode for precise pin-by-pin testing. The manual also provides guidance on using the remote terminator for testing installed cables at wall jacks or patch panels. Caution is advised against using the tester on live circuits and leaving the battery in the device for extended periods without use.

Quick Issues Covered

  • Diagnose open, shorted, and crossed pair faults in cables.
  • Manual mode for precise pin-by-pin cable testing.
  • Includes schematics for circuit tracing and troubleshooting.

Overview

The 231A Multi-Network Cable Tester by BK Precision is a practical tool designed to read the correct pin configuration of various cables, including 10BASE-T, 10BASE-2, RJ45/RJ11 modular, 258A, TIA-568A/568B, and Token Ring cables. It allows for testing of installed cables using a remote terminator and can verify continuity and detect faults such as open, shorted, and crossed pairs. The tester features an easy-to-read display for continuity and fault status, supports remote testing, checks shield wire integrity, and offers both auto and manual scanning modes.

Controls & Indicators

The front-panel controls and indicators of the 231A Multi-Network Cable Tester include an LED display for the sourcing end (Jack 1) and the receiving end (Jack 2), a power switch, an LED scanning mode switch, and a test switch for manual scanning. There are also RJ45 jacks and a ground LED for the receiving end.

Operation

The 231A Multi-Network Cable Tester operates in several modes to test different types of cables. For a Loopback Test using a 10BASE-T cable, plug one end of the cable into the transmitting RJ45 jack on the master unit and the other end into the receiving RJ45 jack. Turn on the power switch. In Auto mode, the upper row of LEDs will scan in sequence, while in Manual mode, the LED for pin 1 will light up. You can switch between Auto and Manual scanning by pressing the Auto/Manual button. Once both ends of the cable are properly connected, the second row of LEDs will illuminate according to the corresponding LEDs in the top row. The LED display will show the pin configuration status of the tested cable. If necessary, switch to Manual mode for pin-by-pin testing by pressing the Test button to advance to the next pin.

For a Modular Cable Test, follow the same steps as the 10BASE-T Cable Test. For a 10BASE2 Cable Test, use BNC adapter cables on both RJ45 jacks and connect the tested cable to each end of the adapters. Follow the same testing procedures as the 10BASE-T test. For a Remote Test, plug one end of the cable into the transmitting RJ45 jack on the master unit and the other end into the remote terminator. If the cable is installed in a patch panel or wall plate, use the included patch cable. Set the Auto/Manual switch to Auto mode for one-person testing and read the test results from the LED display on the remote terminator.

Safety & Warnings

Operating the tester in live circuits may damage the tester. Leaving the battery in the tester for long periods of time without use could drain power from the battery.

Download PDF (194.2 KB)

Leave a Comment