The BK Precision Instruction Manual for models 1620A, 1621A, 1622A, 1623A, 1626A, and 1627A covers the setup, operation, and troubleshooting of DC regulated power supplies, including details on confirming supply range, precautions for connection, and operating environment. It also provides guidance on operation procedures such as stand-alone, serial, and parallel operations, as well as maintenance tasks like fuse replacement and calibration.
Manual Overview
The BK Precision DC Regulated Power Supplies models 1620A, 1621A, 1622A, 1623A, 1626A, and 1627A are designed for precise voltage and current control, suitable for laboratory, industrial, and telecommunication applications. These units can operate in constant voltage or constant current modes, with outputs adjustable via coarse and fine knobs. For troubleshooting, the manual emphasizes checking the supply range and ensuring proper connection of output terminals. The power supplies allow for serial and parallel configurations to increase output voltage or current, respectively. Calibration procedures include voltage and current calibration, as well as voltmeter and ammeter alignment. Error diagnostics are facilitated by the front panel’s analog or LED meters, which display output voltage and current. Maintenance involves replacing the main fuse and ensuring the unit operates within specified ambient conditions. Board-level guidance is not explicitly detailed, but users are advised to avoid unauthorized repairs to maintain warranty coverage.
Quick Issues Covered
- Diagnose power-up failures with voltage and current calibration.
- Resolve error codes using voltmeter and ammeter alignment procedures.
- Use schematics for circuit tracing during maintenance and repairs.
Overview
The BK Precision models 1620A, 1621A, 1622A, 1623A, 1626A, and 1627A are DC regulated power supplies designed for high precision and continuous variability. These units can operate in constant voltage or constant current mode, with outputs adjustable from 0 up to the rated values. They feature separate voltage and current meters for simultaneous monitoring, and allow for coarse and fine adjustments. The power supplies can be connected in series to increase output voltage or in parallel (master/slave configuration) to increase output current. They are suitable for laboratory, industrial, field service, hobby, and telecommunication applications. The manual covers confirming the supply range, precautions for connection, operating environment, panel explanations, operation procedures, and maintenance tasks.
Specifications
- Voltage and current can be adjusted continuously.
- Separate voltage and current meters.
- Natural convection cooling system.
- Input voltage: 220V, 50Hz.
- Operating ambient temperature: 5 to 40°C, 10-80% R.H.
- Dimensions: 205 x 115 x 270mm.
- Weight: Approximate 6Kgs or 7.4Kgs.
- Input fuse: AC 100V, 110V, 120V 3AF; AC 220V, 230V, 240V 2AF.
- Internal fuse: 500mAF.
Controls & Indicators
1. POWER SWITCH: Turns the power supply ON-OFF; the switch lights up when the unit is ON.
2. DC VOLTMETER: Indicates the present output voltage. (Analog meter for 1620, 1622, 1626 and LED meter for 1621, 1623, 1627)
7. VOLTAGE FINE ADJUST: Fine adjust knob for the output voltage in voltage mode.
8. CURRENT COARSE ADJUST: Coarse adjust knob for current limiting point and current value in constant current mode.
Installation / Setup
The source does not provide specific information on installation or setup highlights such as wiring, clearances, calibration, or prerequisites.
Operation
The manual does not provide specific information on operation/modes/basic usage steps.
Safety & Warnings
The manual includes the following safety warnings and precautions:
1. The units must be used within their specified range. Before plugging into the AC supply outlet, check whether the input rating conforms with your local supply. For certain models, a voltage selector is available, and it should be switched to the appropriate position before use.
2. The units are floating type power supplies. For ordinary use, ensure that the MASTER/SLAVE switch on the rear panel is set to the MASTER position and either the (+) output terminal or the (-) terminal is connected to the GND terminal (chassis GND) via the shorting bar.
3. The unit should be used within the specified ambient temperature range listed in the specification table.
4. Because the unit is cooled by natural convection, do not place objects on top that could block the convection. Avoid placing the unit on or near any heat-emitting devices or using multiple units in a stacked configuration. For best results, use the unit in an environment that is as well cross-ventilated as possible.