The Hammarlund Model HX-50 Transmitter/Exciter manual provides detailed instructions for setup, operation, and troubleshooting, including requirements for antenna systems, power sources, and connections for microphones and keys. It also addresses television interference suppression and offers guidance on installation, such as avoiding excessively warm or drafty locations and ensuring proper ventilation.
Manual Overview
The Hammarlund Model HX-50 Transmitter/Exciter service manual provides detailed guidance for troubleshooting, diagnostics, and calibration. The manual emphasizes a systematic troubleshooting flow, beginning with verifying power source compatibility and ensuring proper connections to prevent damage. Error codes and diagnostics are not explicitly detailed, but the manual suggests checking tube functionality and connections if performance issues arise. Calibration involves adjusting the quartz crystal sideband filter and ensuring the C.T.O. direct reading is accurate within 5 Kc/s error between adjacent calibration points. For board-level guidance, the manual describes the tube complement and their functions, such as the 6C10 for sideband switching and the 6DQ5 as the power amplifier. Adjustments may involve replacing or recalibrating these components. The manual also highlights the importance of proper antenna connections and the use of a low pass T.V.I. filter to minimize interference. For installation, it advises avoiding extreme temperatures and ensuring adequate ventilation.
Quick Issues Covered
- Diagnose power-up failures with voltage checks on rectifier V108.
- Adjust frequency calibration using C.T.O. direct reading method.
- Trace circuits using detailed schematics for troubleshooting.
Overview
The Hammarlund Model HX-50 Transmitter/Exciter is designed for SSB, AM, and CW transmission across various amateur bands. It can function as a standalone transmitter or as an exciter for a linear power amplifier. The device requires a 40-80 ohm terminated antenna system, a key or microphone, and a 115-volt AC power source for operation. The HX-50 features a stable quartz crystal sideband filter, built-in antenna change-over relay, and automatic break-in CW keying. It is engineered to minimize television interference and includes a three-element variable pi-network for harmonic suppression.
Specifications
- SSB (Single Sideband, Suppressed Carrier), AM (Amplitude Modulation), and CW (Continuous Wave) transmission
- 160, 80, 40, 20, 15, and 10 meter amateur bands
- 40-80 ohm terminated antenna system
- 115-volt, 50-60 cycle AC power source
- Minimum power output ratings: SSB 50-60 Watts, CW 50-60 Watts, AM 12-14 Watts
- Stable quartz crystal sideband filter operating at approximately 3 Mc/s
- Built-in antenna change over relay
- Time sequenced, automatic break-in CW keying (VOX keying)
- C.T.O. direct reading to 10 Kc/s points with less than 5 Kc/s error between adjacent 100 Kc/s calibration points
- 90 Watts plate input to the final amplifier on SSB, and CW
- Six band output: 80, 40, 20, 15, and 10 meter bands supplied; 160 meter band output available on special order
- 10 meter band coverage in three individually calibrated switched segments
- 105-125 Volts, 50-60 Cycle AC power source
- Power consumption is 250 Watts
Installation / Setup
After unpacking the HX-50 Transmitter/Exciter, inspect it for any transit damage and file a claim with the carrier if necessary. Avoid placing the unit near heat sources or drafts, ensuring adequate space for air circulation. The device operates on a 105-125 Volt, 50-60 Cycle AC power source, consuming 250 Watts. Verify compatibility with your power source to prevent damage. The rear panel includes various connections: a microphone receptacle for high impedance microphones, a key jack for CW operation, an RF output connector for antenna or amplifier connection, a receiver antenna connector, and a station control terminal board for integrating with a station control system.