Hallicrafters S-72 Run 4 Operation and Service Instruction Manual (PDF)

The Hallicrafters Model S-72 manual provides detailed instructions for setting up, operating, and troubleshooting the portable all-wave superheterodyne radio receiver, which includes guidance on using its built-in antennas and connecting to external power sources. It also emphasizes the importance of careful tuning and sensitivity adjustments to minimize noise and ensure optimal reception of both standard broadcast and shortwave signals.

  • Brand: Hallicrafters
  • Model: S-72
  • Type: service manual
  • File size: 3.1 MB

Manual Overview

The Hallicrafters Model S-72 is a portable superheterodyne radio receiver designed for AM and CW reception across standard broadcast and shortwave bands. It uses eight tubes and a selenium rectifier, with built-in loop and whip antennas for signal reception. For troubleshooting, the manual emphasizes careful adjustment of sensitivity and tuning controls to minimize noise. The receiver can operate on both AC/DC power sources or a battery pack, with specific instructions for each mode. Calibration involves setting the BAND SPREAD dial to zero for accurate tuning, particularly important for shortwave reception. The BAND SPREAD control allows fine-tuning by spreading out narrow frequency ranges. For board-level guidance, the manual suggests checking connections and ensuring proper installation of components. Error diagnostics are not explicitly detailed, but operational issues may often be resolved by verifying power connections and antenna setup. The VOICE/CODE control is crucial for switching between AM and CW modes and adjusting sensitivity during code reception.

Quick Issues Covered

  • Diagnose power-up issues with AC/DC and battery operation.
  • Adjust BAND SPREAD for precise shortwave tuning.
  • Calibrate VOICE/CODE control for optimal sensitivity.

Overview

Model S-72 is a portable all-wave superheterodyne radio receiver that covers standard broadcast and both foreign and domestic shortwave bands. It provides AM and CW reception over a frequency range from 540 kilocycles (KC) to 30 megacycles (MC) using eight tubes and a selenium rectifier. The receiver includes built-in antenna facilities with a loop antenna for standard broadcasts and a telescoping whip antenna for shortwave reception. An external antenna terminal is also available for areas with low signal strength. The BAND SPREAD control allows for fine tuning, and the receiver features a built-in 5-inch PM speaker and a PHONES jack for headphones. It can operate from a 105-125 volt DC or 50-80 cycle AC power source, as well as from a self-contained 90 volt – 73 volt battery pack.

Specifications

  • Model S~72 is a portable all-wave superheterodyne radio receiver.
  • Covers standard broadcast and shortwave bands.
  • Frequency range: 540 kilocycles (KC) to 30 megacycles (MC).
  • Equipped with eight ON-OFF tubes and a selenium rectifier.
  • Built-in loop antenna for standard broadcast reception.
  • Telescoping whip antenna for shortwave reception.
  • Terminal for external single wire antenna connection.
  • BAND SPREAD control for fine tuning.
  • Built-in 5 inch PM speaker.
  • PHONES jack for headphones connection.
  • VOICE/CODE control for AM or CW reception.
  • Designed for 105-125 volt DC or 50-80 cycle AC power source.
  • Portable operation from a self-contained 90 volt – 73 volt battery pack.
  • Power consumption: 25 watts.

Controls & Indicators

The front-panel controls/indicators of the Model S~72 include the following: ON-OFF VOLUME control, BAND SELECTOR switch, BAND SPREAD control, TUNING control, VOICE/CODE control, and a PHONES jack for headphones.

Installation / Setup

The Model S~72 radio receiver setup involves several key steps and considerations. It is designed for both portable and fixed operation, requiring a 105-125 volt DC or 50-60 cycle AC power source, or a self-contained 90 volt – 73 volt battery pack for portability. For shortwave reception, clearance must be provided for the fully extended 61-inch whip antenna. The receiver includes built-in loop and whip antennas, with an option to connect an external single wire antenna in areas of low signal strength. When setting up, ensure the BAND SPREAD dial pointer is at 0 for correct calibration of the TUNING dial scales. For battery operation, the battery should not be stored in the compartment to prevent damage from leakage.

Operation

The Model S~72 radio receiver can operate on both battery and AC/DC power sources. For battery operation, a 90 volt – 73 volt battery pack is required, which should be installed in the compartment below the receiver chassis. For AC/DC operation, the receiver can be plugged into a 105-125 volt power source. The receiver has a built-in loop antenna for standard broadcast reception and a telescoping whip antenna for shortwave reception. The BAND SELECTOR switch is used to choose between standard broadcast and shortwave bands. The VOICE/CODE control allows selection between AM and CW reception, with the CODE setting also functioning as a sensitivity adjustment. The BAND SPREAD control is used for fine tuning on shortwave bands. Headphones can be connected via the PHONES jack, which disconnects the speaker when in use.

Download PDF (3.1 MB)

Leave a Comment