Hallicrafters S-72 Run 4 Operation Service Manual (2) (PDF)

The service manual for the Hallicrafters Model S-72 provides detailed instructions for setting up and operating the portable all-wave superheterodyne radio receiver, including guidance on battery and AC/DC power operation, antenna usage, and tuning for both standard broadcast and shortwave bands. It also includes troubleshooting tips such as adjusting sensitivity and tuning controls to minimize noise and improve reception, as well as instructions for connecting headphones and replacing batteries.

  • Brand: Hallicrafters
  • Model: S-72
  • Type: service manual
  • File size: 1.1 MB

Manual Overview

The service manual for the Hallicrafters Model S-72 radio receiver provides detailed instructions for troubleshooting, diagnostics, calibration, and adjustments. The receiver, a portable all-wave superheterodyne radio, covers standard broadcast and shortwave bands from 540 kilocycles to 30 megacycles. It uses eight tubes and a selenium rectifier. Troubleshooting begins with checking power sources, ensuring the correct voltage and frequency, and verifying the connection of antennas. Error diagnostics include verifying the operation of the BAND SELECTOR and VOICE/CODE controls. Calibration involves setting the BAND SPREAD dial to zero for accurate tuning. Adjustments for optimal reception include using the BAND SPREAD control for fine-tuning shortwave frequencies and adjusting the VOICE/CODE control for sensitivity. The manual provides board-level guidance for replacing components, such as tubes and batteries, and emphasizes the importance of using the correct battery type for portable operation. Proper installation and operation are crucial for maintaining the receiver’s high sensitivity and minimizing noise.

Quick Issues Covered

  • Diagnose power-up failures with AC/DC operation guidelines.
  • Adjust sensitivity to minimize noise and background hiss.
  • Fine-tune frequencies using BAND SPREAD control for shortwave reception.

Overview

Model $-72 is a portable all-wave superheterodyne radio receiver that covers standard broadcast and shortwave bands, providing AM and CW reception from 540 kilocycles to 30 megacycles. It uses eight tubes and a selenium rectifier. The receiver includes built-in antenna facilities with a loop antenna for standard broadcast and telescoping whip antennas for shortwave reception. It also has provisions for an external single wire antenna in areas of low signal strength. The receiver features a BAND SPREAD control for fine tuning, a built-in 5-inch PM speaker, and a PHONES jack for headphones. It can operate from a 105-125 volt DC or 50-60 cycle AC power source, or from a self-contained 90 volt – 74 volt battery pack.

Specifications

  • Model $-72 is a portable all-wave superheterodyne radio receiver.
  • Covers standard broadcast and foreign and domestic shortwave bands.
  • AM and CW reception over entire frequency range.
  • Frequency range: 540 kilocycles (KC) to 30 megacycles (MC).
  • Uses 8 tubes and a selenium rectifier.
  • Built-in loop antenna for standard broadcast reception.
  • 2 telescoping whip antennas for shortwave reception.
  • Terminal for external single wire antenna.
  • BAND SPREAD control for fine tuning.
  • Built-in 5 inch PM speaker.
  • PHONES jack for headphone connection.
  • Operates from 105-125 volt DC or 50-60 cycle AC power source.
  • Portable operation from a self-contained 90 volt – 74 volt battery pack.
  • Power consumption: 25 watts.
  • Headphone output impedance: 100 ohms.

Controls & Indicators

The front-panel controls/indicators include a PHONES jack for connecting headphones, an ON-OFF VOLUME control for powering the receiver and adjusting volume, a BAND SELECTOR switch for selecting the desired band, a VOICE/CODE control for selecting between AM (VOICE) and code reception, and a TUNING control for tuning in stations. Additionally, there is a BAND SPREAD control for fine-tuning adjustments.

Installation / Setup

The installation/setup highlights for the Model $-72 radio receiver include:

– The receiver can operate from a 105-125 volt DC or 50-60 cycle AC power source, or from a self-contained 90 volt – 74 volt battery pack.
– For battery operation, the battery pack should be placed in the compartment below the receiver chassis and secured with a battery strap. The battery cable plug must be inserted into the battery receptacle.
– The receiver should not be stored with the battery in the compartment to avoid damage from potential leakage.
– For AC/DC operation, the line cord plug should be inserted into a power outlet, and if using DC, the plug may need to be reversed if the receiver does not operate.
– A special step-down transformer is available for operation from a 220 volt, 50-60 cycle AC source.
– For shortwave reception, clearance for the 61-inch whip antenna is necessary as it must be fully extended for maximum performance.

Operation

The Model $-72 radio receiver can operate in two modes: battery operation and AC/DC operation. For battery operation, a 90 volt – 74 volt battery pack is required. The battery is installed by opening the rear door, placing the battery pack in the compartment, fastening it with a strap, and connecting the battery cable plug to the receptacle. For AC/DC operation, the receiver can be powered from a 105-125 volt DC or 50-60 cycle AC source by plugging the line cord into a power outlet. If using DC and the receiver does not operate, the line cord plug may need to be reversed. A step-down transformer is available for operation from a 220 volt AC source.

For standard broadcast reception, the BAND SELECTOR switch should be set to 1, and the VOICE/CODE control turned to VOICE. The receiver is turned on by rotating the ON-OFF VOLUME control, and stations are tuned using the TUNING control. The built-in loop antenna is used for reception, and the receiver can be rotated for better signal reception.

For shortwave reception, the whip antenna must be fully extended. The BAND SELECTOR switch is set to 2, 3, or 4, and the BAND SPREAD dial pointer is set to 0. The VOICE/CODE control is used for voice or code reception. The receiver is turned on by the ON-OFF VOLUME control, and stations are tuned with the TUNING control. Fine tuning is done using the BAND SPREAD control.

Headphones with an impedance of 500 to 2000 ohms can be connected to the PHONES jack, which disconnects the speaker.

Safety & Warnings

The manual includes the following safety warnings/precautions:

1. Do not store the receiver with the battery in the battery compartment to avoid damage from possible leakage from a dead battery. Store the battery separately in a cool, dry place.
2. If operating on DC and the receiver does not operate after being turned on, reverse the line cord plug.
3. Operation from a 220 volt, 50-60 cycle AC source requires a special step-down transformer. Consult a Hallicrafters dealer for this accessory.

Download PDF (1.1 MB)

Leave a Comment