Hallicrafters S-19R Operation Service Manual (2) (PDF)

The service manual for the Hallicrafters Sky Buddy Model S-19R provides detailed instructions on operating the receiver, including setup with an inverted "L" type antenna and controls for tuning and volume. It also covers troubleshooting and alignment procedures, such as adjusting the intermediate frequency (I.F.) and radio frequency (R.F.) for optimal performance.

  • Brand: Hallicrafters
  • Model: S-19R
  • Type: service manual
  • File size: 91.7 KB

Manual Overview

The Hallicrafters Sky Buddy Model S-19R is a 6-tube, 4-band superheterodyne receiver covering frequencies from 640 KC to 46.0 MC. For optimal operation, an inverted “L” type antenna or a half-wave doublet antenna is recommended. Troubleshooting involves checking connections and ensuring proper antenna setup. Calibration requires setting controls such as the audio gain and A.V.C. switch, and using a signal generator for I.F. alignment at 455 KC. The BFO adjustment involves setting the pitch control to zero beat and verifying the .0005 capacitor and 76 BFO tube if issues persist. R.F. alignment is performed by connecting a generator to the antenna terminal and adjusting trimmers and padders for each band. The manual provides detailed guidance on board-level adjustments and component specifications, ensuring precise tuning and maintenance.

Quick Issues Covered

  • Diagnose power-up failures with 6K8G tube and grid cap removal.
  • Calibrate IF alignment using 455 KC signal generator input.
  • Adjust BFO pitch control for zero beat and check .0005 capacitor.

Overview

The Sky Buddy Model S-19R is a 6-tube, 4-band superheterodyne receiver covering frequencies from 640 KC to 46.0 MC. It is designed for use with an inverted “L” type antenna or a half-wave doublet antenna for optimal performance. The receiver features various controls for tuning and operation, including a main tuning dial, bandspread control, and switches for band selection, beat frequency oscillator, and automatic volume control. The manual provides detailed instructions for operating the receiver, including alignment procedures for both intermediate frequency (I.F.) and radio frequency (R.F.) adjustments.

Specifications

  • Band 1: 640 KC to 1700 KC
  • Band 2: 1.7 MC to 5.5 MC
  • Band 3: 5.5 MC to 17.0 MC
  • Band 4: 16.0 MC to 46.0 MC
  • Tube lineup: 6K8G, 6SK7, 6SQ7GT, 41, 76, 80
  • Power consumption: 5 watts at 117 volts, 60 cycles A.C.

Controls & Indicators

The model S19-R Sky Buddy receiver features several front-panel controls and indicators. These include:

– A main tuning control that rotates a large calibrated dial for frequency selection, with calibration accuracy maintained when the “Bandspread” dial is set to “0” or minimum capacity.
– A “Bandspread” control offering smooth electrical bandspread action, driven by a gearless mechanism.
– A SEND-RECEIVE switch that removes plate voltage from the tubes when in the “send” position.
– A BAND SWITCH for selecting one of the four frequency ranges.
– A B.F.O. “ON-OFF” switch for optional use of the Beat Frequency Oscillator, useful for copying code signals and locating weak signals.
– A PITCH-CONTROL knob to vary the pitch of the beat note when the BFO switch is “on.”
– An A.V.C. “OFF” and “ON” switch for optional use of automatic volume control, which should be “on” for strong signals and “off” for maximum sensitivity.
– A control for turning the receiver on and off, which also adjusts the volume.
– A headphone jack that disconnects the speaker when headphones are used.

Operation

The Sky Buddy Model S19-R is a 6-tube, 4-band superheterodyne receiver covering frequencies from 640 KC to 46.0 MC. For optimal operation, an inverted “L” type antenna 75 feet long is recommended, with a jumper connected between A2 and G. For maximum performance on a specific frequency, a half-wave doublet antenna cut for that frequency can be used. A ground is usually not necessary, but if needed, it can be connected to the “G” post of the antenna terminal strip.

The receiver has several controls for operation:
– The main tuning control rotates the calibrated dial for frequency selection, accurate when the “Bandspread” dial is set at “0”.
– The “Bandspread” control provides smooth electrical bandspread action.
– The SEND-RECEIVE SWITCH removes plate voltage from the tubes in the “send” position.
– The BAND SWITCH selects one of the four frequency ranges.
– The B.F.O. “ON-OFF” SWITCH is used for code signals and helps locate weak signals.
– The PITCH-CONTROL knob adjusts the pitch of the beat note when the BFO switch is on.
– The A.V.C. “OFF” and “ON” SWITCH allows optional use of automatic volume control.
– The receiver is turned on/off and volume adjusted with a control that also serves as the power switch.
– A headphone jack disconnects the speaker when headphones are used.

The tube lineup includes 6K8G, 6SK7, 6SQ7GT, 41, 76, and 80. The receiver draws 5 watts at 117 volts, 60 cycles A.C.

Download PDF (91.7 KB)

Leave a Comment