The Drake DDC864A manual provides detailed instructions for setting up, operating, and troubleshooting the digital downconverter, including information on front panel controls, rear panel connections, and installation requirements. It also covers the specifications for optimal performance and provides guidance on handling error conditions and ensuring proper ventilation to prevent overheating.
Manual Overview
The R.L. Drake DDC864A Digital Downconverter is designed to translate digital ATSC, 8VSB signals to a 44 MHz IF output. Troubleshooting involves monitoring the front panel indicators: the POWER/ERROR indicator (F1) lights up when connected to power and flashes to signal an invalid channel setting or other operational errors, which disables the RF output. The SIGNAL indicator (F2) confirms the presence of a signal, while the Channel Number Switch (F3) allows selection of broadcast TV channels 02 through 69. For diagnostics, ensure the DC power input is correctly connected using the rear panel’s 3-pin connector. Calibration and adjustments are minimal, focusing on channel selection and ensuring proper ventilation in rack-mounted installations to prevent overheating. The device supports a frequency range of 54 to 806 MHz with a noise figure of 10 dB and requires a DC power input of +12 V and +5 V. For optimal performance, maintain the unit within the specified operating temperature of 0°C to +50°C.
Quick Issues Covered
- F1 indicator flashes for invalid channel settings or errors.
- F2 indicator confirms signal presence for diagnostics.
- Channel switch F3 sets operating channel for TV broadcast.
Overview
The R.L. Drake DDC864A is a digital downconverter designed for translating digital ATSC, 8VSB signals from their off-air channel to a 44 MHz IF output. It provides low noise figure, low phase noise, and a flat passband to minimize signal deterioration. The DDC864A is optimized for use with ATSC 8VSB modulation in a 6 MHz wide channel assignment and is suitable for adjacent channel environments. The manual covers front panel controls and indicators, rear panel connections, installation guidelines, and specifications.
Specifications
- Frequency Range: 54 to 806 MHz
- Input level Range: -25 dBmV to +30 dBmV
- Impedance: 75 Ohms, return loss of 8 dB
- Noise Figure: 10 dB, maximum
- Image Rejection: >75 dB
- IF Frequency: 44 MHz
- Level: +30 dBmvV, +1 dB
- Impedance: 75 Ohms, return loss of 20 dB
- Frequency Stability: +30 PPM
- Channel Bandwidth: 6 MHz SAW filtered
- SSB Phase Noise: -88 dBc @ 10 kHz offset
- Amplitude Flatness (6 MHz Channel): +1 dB over 4 MHz
- DC Power Input: +12 V 5% @ 150 mA
- +5 V 45% @ 150 mA
- Operating Temperature: 0°C to +50°C ambient
- Size: 1” Wx 3.5” H x 9.25” D
- Weight: 11 oz.
Controls & Indicators
F1 – POWER/ERROR Indicator: Lights when the unit is connected to the required source of DC power via the rear panel DC INPUT connector. A flashing condition indicates an invalid channel setting or other conditions that would cause the unit to operate on an invalid channel. The RF output is switched off for flashing (ERROR) conditions.
F2 – SIGNAL Indicator: Lights when a signal is present.
F3 – Channel Number Switch: Sets the desired operating channel for standard Broadcast TV channels 02 through 69.
Installation / Setup
The installation of the DRAKE DDC864A digital downconverter requires attention to several key aspects. All connections to and from the unit are made through the rear panel. It is important to ensure proper orientation and wiring when connecting the DC power cable to the 3-pin DC INPUT connector. Adequate ventilation is crucial in multichannel installations; units should be spaced vertically by at least 1.75 inches wherever possible, and some air movement is mandatory in enclosed rack cabinets to prevent excessive heat, which can shorten component life and degrade performance.
Operation
The source does not provide specific information on the operation, modes, or basic usage steps of the DDC864A Digital Downconverter.
Safety & Warnings
Adequate ventilation is very important in multichannel installations. Units should be spaced apart vertically by at least 1.75″ wherever possible, and some air movement is mandatory in enclosed rack cabinets. Excessive heat will shorten component life and performance will be degraded without proper cooling.