The manual provides detailed instructions for installing the internal DMM assembly in the Agilent 34970A, including steps for disconnecting the power, removing the outer cover, connecting cables, and enabling the DMM for operation. It also includes guidance on modifying rear panel labeling and performing a zero adjustment procedure to ensure calibration accuracy.

• Brand: Hp-34970a
• Model: OPT.-001-DMM-INSTALLATION
• Type: manual
• File size: 72.3 KB

Manual Overview

The HP-34970A Option 001 DMM installation manual provides detailed instructions for installing the internal DMM assembly using the 34970-80010 retrofit kit. Begin by disconnecting the power cord and removing the outer cover, following the procedures in chapter 6 of the 34970A Service Guide. Connect the internal DMM ribbon cable to the main circuit board at connector J202, ensuring the locking clips secure the cable. Install the internal DMM circuit board into the chassis, positioning it over the tabs and locking it in place with an audible click. Twist the DMM input cable (P101) once before connecting it to the backplane to maintain specifications. Enable the DMM via the front-panel Utility menu or the remote interface using the INST:DMM command. Modify the rear panel labeling by marking an “X” through the black circle if the DMM was not originally installed. Replace the outer cover as per the service guide. The internal DMM is pre-calibrated, but perform the Zero Adjustment procedure from chapter 4 of the service guide to ensure accuracy.

Overview

Agilent 34970A/Option 001 is a product that involves the installation of an internal DMM assembly using the 34970-80010 Retrofit Kit. The manual provides step-by-step instructions on how to install the internal DMM assembly into the Agilent 34970A, including disconnecting the power cord, removing the outer cover, connecting cables, installing and locking the circuit board, and enabling the internal DMM. It also includes instructions for modifying the rear panel labeling and replacing the outer cover. Calibration information is provided, indicating the internal DMM was pre-calibrated at the factory, and a Zero Adjustment procedure is recommended post-installation.

Specifications

Refer to the PDF for details.

Controls & Indicators

Refer to the PDF for details.

Installation / Setup

To install the Agilent 34970A/Option 001 internal DMM assembly, first disconnect the power cord and remove the outer cover following the procedures in chapter 6 of the 34970A Service Guide. Connect the internal DMM ribbon cable to connector J202 on the main circuit board and secure it with locking clips. Install the internal DMM circuit board into the chassis by positioning it over the tabs and locking it in place. Twist the internal DMM input cable at least one full turn before connecting it to the backplane connector to avoid compromising specifications. Enable the internal DMM from the front-panel or remote interface. Modify the rear panel labeling if necessary, and replace the outer cover. The internal DMM is pre-calibrated, but a Zero Adjustment procedure should be performed as per chapter 4 of the Service Guide.

Operation

Refer to the PDF for details.

Troubleshooting & Error Codes

Refer to the PDF for details.

Safety & Warnings

Refer to the PDF for details.

Download OPT.-001-DMM-INSTALLATION Manual (PDF – 72.3 KB)

HP-34970A OPT.-001-DMM-INSTALLATION manual guides technicians through the installation process of the DMM option.

• Brand: Hp-34970a
• Model: OPT.-001-DMM-INSTALLATION
• Type: Manual
• File size: 72.3 KB

Overview

Brief overview of the product.

Specifications

• Key spec 1
• Key spec 2

Controls & Indicators

Control panel/button layout.

Installation / Setup

1. Step 1…
2. Step 2…

Operation

Basic usage, modes, cycles.

Troubleshooting & Error Codes

Safety & Warnings

• Important warning…

Downloads

Download OPT.-001-DMM-INSTALLATION manual (PDF)

The manual provides detailed instructions for installing the internal DMM assembly in the Agilent 34970A, including steps for disconnecting the power, removing the cover, connecting cables, and enabling the DMM for operation. It also covers troubleshooting tips such as ensuring proper cable connections and modifying rear panel labeling, as well as calibration information to ensure the DMM meets accuracy specifications.

• Brand: Hp-34790a
• Model: OPT.-001-DMM-INSTALLATION
• Type: manual
• File size: 72.3 KB

Overview

Agilent Technologies provides installation instructions for the 34970A/Option 001, specifically for the internal DMM assembly using the 34970-80010 Retrofit Kit. The manual covers steps to disconnect the power cord, remove the outer cover, connect the internal DMM ribbon cable, install and lock the internal DMM circuit board, twist and insert the DMM input cable, enable the internal DMM, modify rear panel labeling, and replace the outer cover. Calibration information is also included, noting that the internal DMM was pre-calibrated at the factory and requires a Zero Adjustment procedure post-installation.

Specifications

Refer to the PDF for details.

Controls & Indicators

Refer to the PDF for details.

Installation / Setup

To install the internal DMM assembly for the Agilent 34970A/Option 001, first disconnect the power cord and remove the outer cover by following the procedures in chapter 6 of the 34970A Service Guide. Connect the internal DMM ribbon cable to connector J202 on the main circuit board and secure it with the locking clips. Install the internal DMM circuit board into the chassis by positioning it over the tabs and locking it in place with a click. Twist the internal DMM input cable at least one full turn before connecting it to the backplane connector to ensure specifications are met. Enable the internal DMM via the Utility menu or remote interface command. Modify the rear panel labeling if necessary, and replace the outer cover. The internal DMM is pre-calibrated, but a Zero Adjustment procedure should be run as outlined in chapter 4 of the Service Guide.

Operation

Refer to the PDF for details.

Troubleshooting & Error Codes

Refer to the PDF for details.

Safety & Warnings

Refer to the PDF for details.

Download OPT.-001-DMM-INSTALLATION Manual (PDF – 72.3 KB)

HP-34790A OPT.-001-DMM-INSTALLATION manual guides technicians through the installation process of the digital multimeter option.

• Brand: Hp-34790a
• Model: OPT.-001-DMM-INSTALLATION
• Type: Manual
• File size: 72.3 KB

Overview

Brief overview of the product.

Specifications

• Key spec 1
• Key spec 2

Controls & Indicators

Control panel/button layout.

Installation / Setup

1. Step 1…
2. Step 2…

Operation

Basic usage, modes, cycles.

Troubleshooting & Error Codes

Safety & Warnings

• Important warning…

Downloads

Download OPT.-001-DMM-INSTALLATION manual (PDF)