The service manual for the Hallicrafters Model S-40 covers setup, operation, and troubleshooting, including details on the radio receiver's 4-band AM/CW reception, power supply data, tube types and functions, and control settings for preliminary test operation. It also provides instructions for restringing dial cords and includes a replacement parts list and alignment instructions.

• Brand: Hallicrafters
• Model: NO.1
• Type: service manual
• File size: 1.4 MB

Manual Overview

The Hallicrafters S-40 service manual provides detailed instructions for servicing this 9-tube superheterodyne radio receiver. For troubleshooting, it emphasizes the use of a signal generator and output meter for alignment, ensuring accurate frequency and sensitivity settings. The manual outlines the IF frequency as 455 kHz and provides specific selectivity and image ratio data for optimal performance. Calibration involves adjusting the sensitivity, volume, and tone controls, with settings provided for preliminary test operations. The manual includes a detailed procedure for restringing the main tuning and bandspread dial cords, requiring specific tools like an Allen wrench and a Spintite wrench. Board-level guidance is offered through a comprehensive parts list, detailing transformers, switches, and sockets, with part numbers for replacements. The manual also specifies rear panel connections and power supply requirements, both for AC and DC operations, ensuring technicians can maintain or repair the receiver effectively.

Quick Issues Covered

• Diagnose power-up failures with AC/DC supply data and settings.
• Adjust sensitivity and AVC using control settings guide.
• Trace circuits with detailed schematic and component list.

Overview

Model S-40 is a 9-tube commercial superheterodyne table model radio receiver. It incorporates 4 bands of AM/CW reception and includes features such as variable sensitivity control, optional AVC, noise limiting, BFO pitch, tone control, headset reception, and the use of an external “S” meter. It also supports standby operation and bandspreading. The manual provides detailed service information, including rear panel connections, power supply data, tube types and functions, control settings for preliminary test operation, dial cord restringing instructions, a replacement parts list, and alignment instructions.

Specifications

• Model S-40 is a 9 tube commercial superheterodyne table model radio receiver.
• Incorporates 4 bands of AM/CW reception.
• Provision for variable sensitivity control.
• Optional AVC, noise limiting, BFO pitch, tone, headset reception, and use of an external "S" meter.
• Standby operation and bandspreading are provided.
• Rear panel connections: AC line cord with plug, antenna and ground connector strip, DC power input socket, and external "S" meter connector socket.
• AC operation: 117 volt, 50/60 single phase source.
• Power drain is 75 watts.
• DC operation: filament 6.3 volt @ 5 amp; "B" supply 260 volt @ 70 ma.
• Tube types and function: 6SG7—RF amplifier; 6SA7—mixer; 6SK7—(2 used)—1st and 2nd IF amplifiers; 68Q7—detector, audio amplifier; GFGG—audio power amplifier; GH6—gas gate and noise limiter; 6]5—BFO; 80—power rectifier.
• IF frequency: 455 ke.
• Selectivity: 6.8 kc wide at 6 db down, 40.7 ke wide at 60 db down.
• Image ratio: 6:1 at 30 me, 15:1 at 14 me, 37:1 at 5 me, 1000:1 at 1500 ke.
• Sensitivity: 15 microvolt for 500 milliwatt output at 550 ke, 8 microvolt for 500 milliwatt output at 40 me.
• Audio output: 1 watt with less than 10% distortion.

Controls & Indicators

The front-panel controls and indicators for the Model S-40 include the following:

1. Sensitivity: RF gain control, set to maximum clockwise.
2. Band Selector: Operating band, set counterclockwise.
3. Volume: Audio gain control, set half clockwise; adjust as necessary.
4. AVC: Automatic volume control, set to “ON.”
5. Tuning: Main tuning control, set to local station frequency on the main dial scale.
6. CW/AM: BFO on/off switch, set to “AM.”
7. Noise Limiter: Noise peak limiting, set to “OFF.”
8. Band Spread: Short wave band spreading, set to “0” on small dial scale.
9. Tone: Receiver on/off switch and tone control, set clockwise to “MED.”
10. Pitch: CW beat note control, any position (not in use).
11. Phones Jack: Headset connection, not used.
12. Standby/Receive: Receiver temporary standby, set to “RECEIVE.”

Installation / Setup

Refer to the PDF for details.

Operation

Model S-40 is a 9-tube commercial superheterodyne table model radio receiver with 4 bands of AM/CW reception. It includes features such as variable sensitivity control, optional AVC, noise limiting, BFO pitch, tone control, headset reception, external S meter use, standby operation, and bandspreading. The rear panel connections include an AC line cord with plug, antenna and ground connector strip, DC power input socket, and external S meter connector socket. For AC operation, it requires a 117-volt, 50/60 single-phase source with a power drain of 75 watts. For DC operation, it requires a filament of 6.3 volts at 5 amps and a B supply of 260 volts at 70 mA. The tube types and their functions are specified, including RF amplifier, mixer, IF amplifiers, detector, audio amplifier, audio power amplifier, gas gate and noise limiter, BFO, and power rectifier.

For preliminary test operation on the broadcast band, the control settings are as follows: Sensitivity at maximum clockwise, Band Selector counterclockwise to 1, Volume half clockwise, AVC at ON, Tuning to local station frequency, CW/AM at AM, Noise Limiter at OFF, Band Spread to 0 on the small dial, Tone to MED, Pitch Control in any position, Phones jack not used, and Standby/Receive at RECEIVE.

To restring dial cords, the front panel must be removed. A No. 6 Allen wrench is needed to loosen the set screws in the knobs. For the main tuning dial cord, a 25-inch length of 18 lb. test dial cord is used, starting at the tension spring of the main tuning capacitor drive pulley. For the bandspread tuning dial cord, a 35-inch length of dial cord is used, starting at a different position on the diagram.

Troubleshooting & Error Codes

Refer to the PDF for details.

Safety & Warnings

Refer to the PDF for details.

Download NO.1 Service manual (PDF – 1.4 MB)

Hallicrafters S-40 Service Bulletin NO.1 PDF helps technicians troubleshoot and repair the S-40 model efficiently. File size: 1.4 MB.

• Brand: Hallicrafters-s-40-service-bulletin
• Model: NO.1
• Type: Service manual
• File size: 1.4 MB

Overview

Brief overview of the product.

Specifications

• Key spec 1
• Key spec 2

Controls & Indicators

Control panel/button layout.

Installation / Setup

1. Step 1…
2. Step 2…

Operation

Basic usage, modes, cycles.

Troubleshooting & Error Codes

Safety & Warnings

• Important warning…

Downloads

Download NO.1 service manual (PDF)