Introduction

WCA942M M(WCA943M M) is a highly integrated single-chip that features a low power 2 2×2 11a/b/g/n/ac/ax dual-band Wi-Fi subsystem and a Bluetooth the v5.2 subsidy system, offering ng feature-rich h wireless con nnectivity at a high standard, and delivery ing reliable, cost-effective throughput from an extended distance.

Product Details

-Data Modulation

DSSS: CCK, BPS K, QPSK for 802.11b
OFDDM: BPSK,QPPSK,16QAMM,64QAM,2566QAM for 8002.11a,g,n,ac,ax
FHSS:GFSK,OQPSK, 8DPSKK, π/4DPSK ffor Bluetooth.

Frequency Range

2.4GHz:2402-2480MHz, 2412-2472MHz
5GHz:5180-5825MHz

Output Power tolerance
Output power ± 2.5dBm

-Recommended Operating conditions

MinTyp.MaxUnit
Operating voltage4.555.5V
Operating temperature(ambient)-202550°C

Approval Statement

CE approval

-This device is restricted to indoor use only within the 5.15 ~ 5.35GHz Band. (Europe)

Frequency Range and Maximum Output Power (EIRP)

2400 MHz to 2483.5 MHz: Below 20 dBm for Bluetooth 2400 MHz to 2483.5
MHz : Below 20 dBm for 802.11b/g/n 5150MHz to 5250
MHz : Below 23 dBm for  802.11a,n,ac 5350MHz to 5725
MHz :
 Below 20 dBm for 802.11a,n,ac 5725MHz to 5875 MHz : Below 14 dBm for 802.11a,n,ac

SAMSUNG WCA942M Highly Integrated Single Chip - Icon

FCC approval

This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesirable e operation.

To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product.

Contains Transmitter Module FCC ID: A3LWCA942M

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
-The OEM integrator is r responsible for ensuring the end-user has no manual instruction to remove or install the module.
-The module is limited to installation in mobile or fixed applications.

IC approval

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

  • This device may not cause interfere
  • This device must accept any interference, including interference that may cause undesired operation of the

The host device must be labeled to display the Industry Canada certification number of the module.

Contains transmitter module IC:649E-WCA942M

IMPORTANT NOTE

 This device complies with FCC & IC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and must not be co-located or operating in conjunction with any other antenna or transmitter.

This device is intended only for OEM integrators under the following conditions:

  • This module may not be co-located with any other transmitters or
  • The antenna must be installed such that 20cm is maintained between the antenna and

As long as the 2 conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements with this module installed. In the event that these conditions cannot be met, then the FCC & IC authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product including this module, and obtaining separate FCC & IC authorizations.

User Information

Caution: Any changes or modifications not expressly approved by the party void the user`s authority to operate this equipment. esponsible for compliance could

-This device is restricted to indoor use only within the 5.15 ~ 5.25GHz Band. (Canada) .
-Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 56 0-5850 MH and that these radars could cause interference and/or damage to LE-LAN devices.

Version 1.0

Documents / Resources

SAMSUNG WCA942M Highly Integrated Single Chip [pdf] User Manual
WCA942M, A3LWCA942M, WCA942M, Highly Integrated Single Chip

Leave a comment

Your email address will not be published.