STACKING KIT INSTALLATION INSTRUCTIONS (WASHER & DRYER ONLY)

 CAUTION : Two people are required to lift the dryer on to the washer.

 WARNING : These washer and dryer are not suitable for mobile home or RV installation.

Dryer

STEP 1 :  Have two persons place the dryer on a non-slippery floor. Then, have one person tilt the dryer to the side. Do not lay the dryer down. The dryer may be scratched.
STEP 2-1 :  SKK-7*, SKK-8*: Check if the legs are tightened up, and then insert the stacking support guides in the rectangular holes of the dryer’s base until you hear a clicking sound. You don’t need to remove the legs.
STEP 2-2 : SKK-BB: Disassemble legs, and Snap the stacking support guides into the rectangular holes in the dryer base and secure each with two(2) screws Phillips-pan head (6006-001174)
STEP 3 :  Repeat the same step above on the other side.
Dryer
STEP 4 : Bottom view of the dryer after assembling the Stacking Support Guides to the dryer base. * Use a stacking-kit compatible with the purchased model.
Dryer

Washer (Stacking kit: SKK-7*, SKK-8*, for 27” models)

CAUTION : You need to use the proper rear bracket depending on your washer model. (There are 2 different rear brackets : DC61-04160A, DC61-04955A)

5-1) DC61-04160A : WF5*K**, WF4*H**, WF4*K**, WF4*M**, WF4*N**, WF18H**, WF20H**, WF20M**, WF22H**, WF22K**, WF15K**, WF16J65**

Washer (Stacking kit: SKK-7*, SKK-8*, for 27” models)

DO NOT TIGHTEN SCREWS COMPLETELY
STEP 5-1 :  LOOSELY assemble the Rear Brackets (DC61-04160A) to the washer as shown below. Use two (2) Screws-Hex Head (6002-001431) with washers (DC60-00044A) in each washing machine Top Cover tail, per bracket. * Before installing the rear bracket, loosen two screws (Screw-Hex) on the Cover Top that is secured to the frame.

5-2) DC61-04955A : WF5*R**, WF4*R**\

Washer (Stacking kit: SKK-7*, SKK-8*, for 27” models)

DO NOT TIGHTEN SCREWS COMPLETELY
STEP 5-2 :  LOOSELY assemble the Rear Brackets (DC61-04955A) to the washer as shown below. Use two (2) Screws-Hex Head (6002-001431) with washers (DC60-00044A) in each washing machine Top Cover tail, per bracket. * Before installing the rear bracket, loosen two screws (Screw-Hex) on the Cover Top that is secured to the frame.

Washer (Stacking kit: SKK-BB, for 30” models)

WF56H** : 

STEP 5-3 :  Loosely assemble the Rear Bracket (DC61-03846A) to the washer as shown above in either case A or Case B, Use (2) Screws-Hex Head (6009-001476) with washers (DC60-00044A) to the each hole of Cover Top and Frame. * Case A only : Before installing the rear bracket, loosen two screws (Screw-Hex) on the Cover Top that is secured to the frame.

diagram

STEP 6 :  Lift and position dryer into the position on the washer shown above, slide dryer backwards to make contact with rear brackets
STACKING KIT INSTALLATION INSTRUCTIONS (WASHER & DRYER ONLY)

CAUTION : To prevent noise, check the followings.

  • Make sure the washer is level.
  • Make sure the dryer’s leveling legs are tightened up. (Stacking kit: SKK-7*, SKK-8*, for 27” models).

STEP 7 :  Align rear brackets with mounting holes on the rear of dryer as shown above.
STACKING KIT INSTALLATION INSTRUCTIONS (WASHER & DRYER ONLY)
STEP 8 :  LOOSELY assemble rear brackets to the back of the dryer using two (2) Screws- Phillips Pan Head (6006-001174) for each rear bracket as shown above. Extra screws may be included with this kit.
STACKING KIT INSTALLATION INSTRUCTIONS (WASHER & DRYER ONLY)
STEP 9 : Tighten screws on the dryer side of the rear bracket.
STACKING KIT INSTALLATION INSTRUCTIONS (WASHER & DRYER ONLY)

WARNING : Additional gas hook-up components are required for gas dryer.

STEP 10 :  Tighten screws on the washer side of the rear bracket.

  • DO NOT REVERSE THE ORDER OF STEPS 9 & 10.
    STACKING KIT INSTALLATION INSTRUCTIONS (WASHER & DRYER ONLY)

STEP 11 : Stacked Unit is now ready to be installed. Refer to detailed installation instructions packed with products.
STACKING KIT INSTALLATION INSTRUCTIONS (WASHER & DRYER ONLY)

Stacking kit components
Stacking Support Guides (2)SKK-7*, SKK-8* –– DC61-04159A
Rear Bracket (2) (WF5*K**, WF4*H**, WF4*K**, WF4*M**, WF4*N**, WF18H**, WF20H**, WF20M**, WF22H**, WF22K**, WF15K**, WF16J65**SKK-7*, SKK-8*– DC61-04160A
Rear Bracket (2) (WF5*R**, WF4*R**)SKK-7*, SKK-8* –– DC61-04955A
Stacking Support Guides (2)SKK-BB– DC61-01480B
Rear Bracket (2) (WF56H**SKK-BB– DC61-03846A
Screws-Hex Head (4)SKK-BBSKK-7*, SKK-8* – 6009-001476
Screws Phillips-Pan Head (8)– 6006-001174
Washer (4)– DC60-00044A
  • Rear Bracket :  (WF5*K**, WF4*H**, WF4*K**, WF4*M**, WF4*N**, WF18H**, WF20H**, WF20M**, WF22H**, WF22K**, WF15K**, WF16J65**)
    Stacking kit components
  • Rear Bracket : (WF56H**)
    Stacking kit components
  • Rear Bracket : (WF5*R**, WF4*R**)
    Stacking kit components
  • Screw-Hex Head : SKK-BB (M5, L10) SKK-7*, SKK-8* (M5, L16)
    Stacking kit components
  • Screw Phillips-Pan Head : (M4, L12)
    Stacking kit components
  • Washer : (ID5, OD10)
    Stacking kit components
  • Stacking Support Guide

Documents / Resources

SAMSUNG Washer and Dryer Stacking Kit [pdf] Installation Guide
Washer and Dryer Stacking Kit

Leave a comment

Your email address will not be published.