Installation
The power of the charger must be on at all times.

SAMSUNG SR10J5050U Robotic vacuum – Installation

NOTE

Install the charger in a place where the floor and wall are level.
Install the charger along the grain of wooden floors.
If the power switch is off, the robot vacuum cleaner will not charge even if it is docked on the charger.
Always turn on the power of the charger.
– If power is not supplied to the charger, the robot vacuum cleaner cannot find it and cannot automatically recharge.
– If the robot vacuum cleaner is left detached from the charger, the battery will drain naturally.
If the robot vacuum cleaner is in energy-saving mode, power will not come on even if the power switch is turned off and then on. Press and hold the Start/Stop button on the robot vacuum cleaner.
Accessories
SAMSUNG SR10J5050U Robotic vacuum – Accessories

Charging
It takes approximately 120 minutes to completely charge when charging for the first time after purchase and can be used for approximately 90 minutes.

SAMSUNG SR10J5050U Robotic vacuum – Charging

Turn on the power switch on the bottom.
You must turn on the power switch to turn on the robot vacuum cleaner.SAMSUNG SR10J5050U Robotic vacuum – Turn on the power
Manually charge the robot vacuum cleaner by placing it on the charger.
Make sure the charge pins of the robot vacuum cleaner and the charger is aligned.SAMSUNG SR10J5050U Robotic vacuum – Manually charge
Check the charging status.
“charging status” will turn on according to charging progress and “FULL” will turn on when charging is complete.SAMSUNG SR10J5050U Robotic vacuum – Check the charging
Automatic charging
When the battery indicator blinks during cleaning, the robot vacuum cleaner will return to the charger to charge itself automatically.

SAMSUNG SR10J5050U Robotic vacuum – Automatic chargingRecharge
You can command the robot vacuum cleaner to recharge at the charger while it is in cleaning process.

SAMSUNG SR10J5050U Robotic vacuum – Recharge

Low battery (Lo)
Manually charge the robot vacuum cleaner by placing it on the charger.

SAMSUNG SR10J5050U Robotic vacuum – Manually charge

√ Steps to take if recharging is not being executed.
Check the installation status of the charger when:

the charger is located in a place where the robot vacuum cleaner cannot easily access it.
distance between the charger and robot vacuum cleaner is over 5 m apart.
– It may take a long time for the robot vacuum cleaner to return to the charger for recharging.
Manually charge the robot vacuum cleaner when:

the charger is located in a corner.
the battery is fully exhausted.
the robot vacuum cleaner is stuck by obstacles (furniture etc.).
the robot vacuum cleaner can’t climb the threshold near charge. (Height of the threshold that the robot vacuum cleaner can climb: about 1.5 cm and below)
when the battery indicator blinks and “Lo” is displayed.
when the robot vacuum cleaner is set on Spot clean or Manual clean mode.
Installing the virtual guard (Optional)
Infrared ray from the Virtual guard will restrict the robot vacuum cleaner from approaching certain areas.

SAMSUNG SR10J5050U Robotic vacuum – virtual guard

The distance of the virtual wall is 2.5 m at a minimum and may differ depending on the surroundings and movement status of the robot vacuum cleaner.

Press the Power button to turn it on.SAMSUNG SR10J5050U Robotic vacuum – Power button
Install the Virtual guard where you want to restrict the robot vacuum cleaner’s entrance.
Make sure that the distance sensor is facing in the desired direction you want to create an invisible barrier (which will restrict the robot vacuum cleaner’s approach).
Part name of the virtual guard
SAMSUNG SR10J5050U Robotic vacuum – Part name

Inserting batteries

Batteries for the Virtual guard must be purchased separately.

Open the battery cover of the Virtual guard by pressing the locking tab and lift it up.SAMSUNG SR10J5050U Robotic vacuum – Open the battery
Insert the batteries (D type) as shown in the illustration (check the +, – polarity).SAMSUNG SR10J5050U Robotic vacuum – Insert the batteries
Insert the tip of the cover into the slot and push the other end to close the battery cover. SAMSUNG SR10J5050U Robotic vacuum – slot and push
Operations
Using the robot vacuum cleaner
You must turn on the power switch before using the robot vacuum cleaner.

SAMSUNG SR10J5050U Robotic vacuum – Turning the power on

Turning the power on/off
Turn on/off the power switch on the bottom of the robot vacuum cleaner.

SONIQ E24FB40A 24 FHD LED LCD TV -WARNING WARNING

When the robot vacuum cleaner is not used for 10 minutes, power will turn off automatically.
SAMSUNG SR10J5050U Robotic vacuum – Using auto clean mode Using auto-clean mode
The robot vacuum cleaner moves and cleans automatically until it cleans an entire space once.
*Stop cleaning: Press thecleaning button shortly
SAMSUNG SR10J5050U Robotic vacuum – cleaning modes Using the cleaning modes
You can select the desired cleaning mode.
SAMSUNG SR10J5050U Robotic vacuum – Recharge Recharge
You can command the robot vacuum cleaner to recharge at the charger automatically while it is in the cleaning process.
SAMSUNG SR10J5050U Robotic vacuum – Setting schedule Setting schedule
You can set or cancel an on-time or daily schedule.

  • Refer to “Setting the schedule”.
    Selecting cleaning mode
    SAMSUNG SR10J5050U Robotic vacuum – Selecting cleaning mode

*When the robot vacuum cleaner is being charged, you can only select the Auto clean, Max cleans or Edge clean mode.

Cleaning method for each mode
SAMSUNG SR10J5050U Robotic vacuum cleaner – Auto clean Auto clean
Cleans automatically until an entire space is cleaned once.
SAMSUNG SR10J5050U Robotic vacuum cleaner – Max clean Auto clean
Cleans automatically until an entire space is cleaned once.
SAMSUNG SR10J5050U Robotic vacuum cleaner -Edge clean Edge clean
Cleans the corners by reaching to them as close as possible.
SAMSUNG SR10J5050U Robotic vacuum cleaner – Spot clean Spot clean
Cleans a localized area intensely. It can be used to clean bread or cookie crumbs.
SAMSUNG SR10J5050U Robotic vacuum cleaner – Manual clean Manual clean
You can move the robot vacuum cleaner with the remote control to clean the desired spot.
SAMSUNG SR10J5050U Robotic vacuum cleaner – Point cleanin

05 Point cleaning
Only available with A-type remote control You can use the remote control to point and clean the desired spot while the robot vacuum cleaner is in the cleaning process.

Point the red light on the floor within 40 cm around the robot vacuum cleaner’s location.
Press and hold the Point cleaning button to move the red light to the desired spot.
The robot vacuum cleaner will follow the light while cleaning. Operating distance of the remote control.

Height of the remote control 0.5 m 1 m 1.5 m
Operating distance About
1.5 m About
2 m About
2.5 m
√ Inserting batteries
Open the battery cover by lifting it up while pressing the locking tab and insert the batteries as shown in the illustration. Then, close the cover until it clicks into place.

SAMSUNG SR10J5050U Robotic vacuum cleaner – Inserting batteries

Name of each part
SAMSUNG SR10J5050U Robotic vacuum cleaner – Name of each part Top
Quick Empty cover (Option)
Dustbin button
Dustbin
Display panel
Remote control sensor
Obstacle sensor
Virtual guard sensor (Option)
Bumper sensor
Bottom
Cliff sensor
Side brush
Charge pin
Roller
Driving wheel
Battery cover
Power brush
Power brush cover
Power switch
Display panel
Start/Stop button
Number display
Daily schedule
One-time schedule
Auto clean
Spot clean
Max clean
Manual clean
Battery indicator
Recharging
Cleaning mode button
Schedule button
Recharge button
Cleaning and maintaining
You must turn off the power switch before cleaning the robot vacuum cleaner.
Cleaning the dustbin
Clean the dustbin if there’s too much dust in the dustbin.

SAMSUNG SR10J5050U Robotic vacuum cleaner – Cleaning the dustbin 1 1. Remove the dustbin SAMSUNG SR10J5050U Robotic vacuum cleaner – Cleaning the dustbin 3 2. Open the dustbin cover
SAMSUNG SR10J5050U Robotic vacuum cleaner -Cleaning the dustbin 2 3. Remove the filter from the dustbin SAMSUNG SR10J5050U Robotic vacuum cleaner – Cleaning the dustbin4 4. Remove dust in the dustbin and the filter
SAMSUNG SR10J5050U Robotic vacuum cleaner – Cleaning the dustbin 5 5. Wash the dustbin and the filter SAMSUNG SR10J5050U Robotic vacuum cleaner – Cleaning the dustbin 6 6. Reassemble the filter into the dustbin
SAMSUNG SR10J5050U Robotic vacuum cleaner – Cleaning the dustbin 7 7. Close the dustbin cover SAMSUNG SR10J5050U Robotic vacuum cleaner – Cleaning the dustbin 8 8. Reinsert the dustbin into the robot vacuum cleaner
Emptying the dustbin (Quick Empty)
Use the Quick Empty cover for emptying the dustbin easily.

SAMSUNG SR10J5050U Robotic vacuum cleaner – Emptying the dustbin 1 1 Open the Quick Empty cover
SAMSUNG SR10J5050U Robotic vacuum cleaner – Emptying the dustbin 2 2 Remove dust in the dustbin with a vacuum cleaner
SAMSUNG SR10J5050U Robotic vacuum cleaner – Emptying the dustbin3 3 Close the Quick Empty cover
Maintenance
Cleaning the driving wheel

SAMSUNG SR10J5050U Robotic vacuum cleaner – Cleaning the driving wheel 1 1 Put a soft cloth on the floor and place the robot vacuum cleaner upside-down
SAMSUNG SR10J5050U Robotic vacuum cleaner – Cleaning the driving wheel 2 2. Use a blunt rod or tweezers to remove the foreign matters
Cleaning the sensors and the camera
Lightly wipe with soft cloth.

SAMSUNG SR10J5050U Robotic vacuum cleaner – Cleaning the sensors

SAMSUNG SR10J5050U Robotic vacuum cleaner – power brush 1. Remove the dustbin SAMSUNG SR10J5050U Robotic vacuum cleaner – power brush 2 2. Remove the power brush cover
SAMSUNG SR10J5050U Robotic vacuum cleaner – power brush 3 3. Remove the power brush SAMSUNG SR10J5050U Robotic vacuum cleaner – power brush 4 4. Clean the power brush
SAMSUNG SR10J5050U Robotic vacuum cleaner – power brush 5 5. Reassemble the power brush SAMSUNG SR10J5050U Robotic vacuum cleaner – power brush 6 6. Reassemble the power brush cover
Cleaning the side brush
Clean the side brush if there’s foreign matter on the brush.

SAMSUNG SR10J5050U Robotic vacuum cleaner – side brush 1 1. Dip a soft cloth into warm water
SAMSUNG SR10J5050U Robotic vacuum cleaner – side brush 2 2. Wrap the side brushes with the cloth for about 10 seconds and then wipe it
If hair or string is caught between the main unit and the side brush, follow the below steps.

SAMSUNG SR10J5050U Robotic vacuum cleaner – main unit 1 1. Remove the side brushes
SAMSUNG SR10J5050U Robotic vacuum cleaner – main unit 2 2. Clean the side brushes
SAMSUNG SR10J5050U Robotic vacuum cleaner – main unit 3 3. Reassemble the side brushes
Documents / Resources
SAMSUNG SR10J5050U Robotic vacuum cleaner [pdf] User Manual
SR10J5050U, Robotic vacuum cleaner

Leave a comment

Your email address will not be published.