The LeCroy WaveJet 300 Series Remote Control Manual provides detailed instructions on setting up and operating the WJ-GPIB and WJ-LAN interface boards, including installation procedures, device behavior, and command functionalities. It also addresses troubleshooting aspects such as buffer size limitations, response formats, and the impact of various commands on device states.
Overview
The WaveJet 300 Series Oscilloscopes Remote Control Manual covers the use of WJ-GPIB and WJ-LAN interface boards for remote control of the WaveJet3xx series. These boards are inserted into option slots on the oscilloscope and allow for remote interface selection. The manual includes installation procedures, interface functions, and device behavior details.
Specifications
- Applicable standard GPIB IEEE-488.1
- Usable unit WaveJet 3xx series firmware 3.xx or later
- Power supply Supplied from WaveJet3xx option slot
- Power consumption Included in WaveJet3xx main unit
- Dimensions 63 mm x 80 mm (excluding protrusion of connector terminal)
- Mass Approximately 70 g
- Operating temperature 0 to 40
Controls & Indicators
Refer to the PDF for details.
Installation / Setup
The source provides information on the installation of the WJ-GPIB and WJ-LAN interface boards for the WaveJet 300 series oscilloscopes. The boards should be inserted into one of the option slots on the rear of the WaveJet3xx unit, with the power turned off to prevent damage. Only one type of interface board can be selected at a time, and inserting two of the same type is prohibited. The boards are sensitive to electrostatic discharge, so anti-static procedures should be followed when handling them.
Operation
Refer to the PDF for details.
Troubleshooting & Error Codes
Refer to the PDF for details.
Safety & Warnings
Refer to the PDF for details.
Download MANUAL Manual (PDF – 803.9 KB)
Lecroy WaveJet 300 Series Remote Control Manual: Guide for technicians on setup, operation, and troubleshooting of remote control functions.
- Brand: Lecroy-wavejet-300-series-remote-control
- Model: MANUAL
- Type: Manual
- File size: 803.9 KB
Overview
Brief overview of the product.
Specifications
- Key spec 1
- Key spec 2
Controls & Indicators
Control panel/button layout.
Installation / Setup
- Step 1…
- Step 2…
Operation
Basic usage, modes, cycles.
Troubleshooting & Error Codes
| Issue / Code | Fix |
|---|---|
| Example | How to fix… |
Safety & Warnings
- Important warning…
Downloads
Lecroy Wavejet 300 Series Remote Control Overview
The Lecroy Wavejet 300 Series Remote Control is a precision instrument designed to facilitate remote operation and control of Lecroy Wavejet oscilloscopes. This device enables users to interact with their oscilloscope from a distance, improving workflow efficiency and allowing for more flexible testing environments. Ideal for laboratory, industrial, and educational applications, the remote control provides seamless access to key oscilloscope functions without the need to be physically present at the instrument.
Main Features and Specifications
- Compatible with Lecroy Wavejet 300 Series oscilloscopes
- Ergonomic design for comfortable handheld use
- Intuitive button layout for quick access to essential oscilloscope controls
- Wireless connectivity with secure signal transmission
- Long battery life supporting extended operation sessions
- Compact and lightweight for portability
- LED indicators for status and battery level
- Robust construction suitable for laboratory and industrial environments
Basic Usage and Operation Tips
To use the Lecroy Wavejet 300 Series Remote Control, first ensure it is properly paired with the oscilloscope. Power on the remote control and verify the connection status via the LED indicators. Use the clearly labeled buttons to navigate menus, adjust settings, and trigger measurements remotely. For optimal performance, keep the remote control within the recommended operating range and avoid physical obstructions between the remote and the oscilloscope. Regularly check battery levels and replace or recharge batteries as needed to prevent interruptions during critical measurements.
Troubleshooting and Maintenance
If the remote control fails to connect, verify that the oscilloscope’s remote function is enabled and that both devices are within range. Restarting both the oscilloscope and the remote control can resolve common connectivity issues. Clean the remote control periodically using a soft, dry cloth to remove dust and debris. Avoid using harsh chemicals or abrasive materials. If buttons become unresponsive, inspect for physical damage and consult the service manual for repair instructions. Always store the remote control in a dry, cool place when not in use to prolong its lifespan.
Safety Reminder
Always follow standard electrical safety precautions when operating the Lecroy Wavejet 300 Series Remote Control. Do not expose the device to moisture or extreme temperatures. Avoid dropping or subjecting the remote control to strong impacts. Use only the recommended batteries and chargers to prevent damage or fire hazards. Keep the remote control away from children and untrained personnel to ensure safe and proper use.
More manuals from Lecroy
- Lecroy-zd500-zd1000-zd1500-owner MANUAL – Manual (PDF)
- Lecroy-zd200-operation MANUAL – Operation manual (PDF)
- Lecroy-x-stream-oscilloscopes-operation MANUAL – Operation manual (PDF)
- Lecroy-wp03-operation-programming MANUAL – Operation manual (PDF)
- Lecroy-wavesurfer-xs-series-getting-started MANUAL – Manual (PDF)