JBL-logo

JBL Stadium 10 Marine Speaker

JBL-Stadium-10-Marine-Speaker-Product

THANK YOU FOR YOUR PURCHASE 
Your JBL product has been designed to provide you with the performance and ease of operation you would expect from JBL.
ABOUT THE MANUAL
This manual describes general installation guidelines. However, please note that proper installation of marine audio components requires qualified experience. If you do not have the knowledge and tools to successfully perform this installation, we strongly recommend consulting an authorized JBL dealer about your installation options. Keep all instructions and sales receipts for reference.

WHAT’S IN THE BOX

JBL-Stadium-10-Marine-Speaker-fig-1

DIMENSIONSJBL-Stadium-10-Marine-Speaker-fig-2
JBL-Stadium-10-Marine-Speaker-fig-3SPEAKER SIGNAL WIRING

JBL-Stadium-10-Marine-Speaker-fig-4

To send signal to the JBL manne speaker, connect the positive(+) and negative(-) speaker wires to the appropriate speaker outputs of your source unit or amplifier. Be sure to observe proper polarity.

SPEAKER LED WIRING

JBL-Stadium-10-Marine-Speaker-fig-5

To provide power for the LEDs, plug the 24-gauge black(+), blue, green, and red LED wires from the speaker into the included female connector, then run the wires from the female connector to your compatible 12-volt power source or light controller (sold separately). If using a separate controller, be sure to connect each wire to the proper output.

If hardwiring the LEDs directly to your power source, you can choose the color of the LEDs by connecting the black wire to the positive (+) terminal, and the appropriate R, G, and/or B single wire or combination of wires to the negative (-) terminal. There are 7 possible colors, depending on the wiring configuration you choose:

Wire connected to positive (+12V) terminalThe wire connected to negative (-) terminalColor produced
     BlackRedRed
GreenGreen
BlueBlue
Red+ GreenYellow
Red+ BluePurple
Blue+ GreenAquamarine
Red + Blue + GreenWhite                                       –

APPLYING FOAM SEAL

JBL-Stadium-10-Marine-Speaker-fig-6

To help seal your installation against water, and to provide an airtight acoustic seal, apply the self-adhesive foam seal to the speaker frame.

MOUNTING THE SPEAKER

JBL-Stadium-10-Marine-Speaker-fig-7

Use the included screws to mount the speaker to the location. Use the included speed clips if necessary to provide a secure mount.
NOTE: Use caution when cutting and using screws with fiberglass to prevent scratches and cracks.

REMOVING THE TWEETER FOR SEPARATE MOUNTING (STADIUM 8 ONLY)

JBL-Stadium-10-Marine-Speaker-fig-8

Use the included 2-pin tool to remove the tweeter from the woofer housing. Place the pins of the tool in the holes of the tweeter grille and rotate 45 degrees clockwise to loosen and remove.

FLUSH-MOUNTING THE TWEETER

JBL-Stadium-10-Marine-Speaker-fig-9

Place the tweeter in the mounting bracket and use the tool to secure by turning 45 degrees counter-clockwise.

JBL-Stadium-10-Marine-Speaker-fig-10

To transmit audio signal to the tweeter, make sure the woofer and tweeter are connected with the included cable.

JBL-Stadium-10-Marine-Speaker-fig-11

Place the tweeter in the mounting location, then turn each setscrew clockwise to tighten the mounting brackets. Use caution so as not to overtighten. Snap the included outer ring over the mounting bracket to hide the setscrews.

MOUNTING IN AN ENCLOSURE (STADIUM 10 ONLY)

JBL-Stadium-10-Marine-Speaker-fig-12

SEALED-BOX VOLUME (INCLUDES DRIVER DISPLACEMENT)JBL-Stadium-10-Marine-Speaker-fig-13

SizeTuning frequency
Free air40Hz
2 ft3 (56.6L)52.2Hz
3 ft3 (85L)48.3Hz
4 ft3 (113L)46.3Hz

VENTED-BOX VOLUME (INCLUDES DRIVER DISPLACEMENT)JBL-Stadium-10-Marine-Speaker-fig-14

SizePort lengthPort diameterTuning frequency
2 ft3 (56.6L)7-9/32″ (185mm)3-15/16″ (100mm)41Hz
3 ft3 (85L)5-1/2″ (140mm)3-15/16″ (100mm)40.6Hz
4 ft3 (113L)4-1/4″ (108mm)3-15/16″ (100mm)40.4Hz

Technical Data

TECHNICAL DATATHIELE-SMALL PARAMETERSStadium Marine 10” (250mm) Subwoofer 2-ohmStadium Marine 10″ (250mm)Subwoofer 4-ohm
Voice coil DC resistance:Rev(OHMs)1.963.7
Electrical inductance:lc:Es (mH)10.4917.52
Driver radiating area:SD (CM2)356.33356.33
Motor force factor:Bl (TM)8.95311.491
Compliance Volume:VAS (Liters)23.523.8
Suspension compliance:CMS (mm/N)0.1310.133
Moving mass, air load:MMS (Grams)107.338106.389
Moving mass, without air load:MMD (Grams)99.73798.789
Free-air resonance:F5 (Hz)42.542.4
Mechanical 0: OMS9.9134.025
Electrical 0: O ES0.6990.793
Total 0: OTS0.6530.663
SPL, 1W/1m @ 4ohm:Lm {dB)86.1485.62

Specifications

SpecificationsStadium 6Stadium 8Stadium 10
Continuous power handling100W200W300W
Peak power handling300W500W900W
Frequency response40Hz-25kHz30Hz-22kHz20Hz- 2kHz
Nominal impedance3 Ohms*3 Ohms*2 or 4 Ohms (use switch to select)
Sensitivity92dB92dB89dB
External diameter7-15/32″ (189.4mm)9-1/2″ (241mm)11- 5/8″ (295.3mm)
Mounting cutout diameter5-23/32″ (144.8mm)Woofer: 7″ (177.4mm) Tweeter bracket: 4-9/16″{115.9mm)9-9/16″ (235.6mm)
Total depth3-21/32″ (92.5mm)4-5/8″ {117.2mm)6-9/16″ {167mm)
Mounting depth2-9/16″ (65mm)3-3/16″ (80.5mm)4-7/8″ {123mm)

HARMAN International Industries, Incorporated 8500 Balboa Boulevard, Northridge, CA 91329 USA www.jbl.com

Documents / Resources

JBL Stadium 10 Marine Speaker [pdf] Owner’s Manual
109STADM62, Stadium 6, Stadium 8, Stadium 10, Marine Speaker, Stadium 10 Marine Speaker

References

Leave a comment

Your email address will not be published. Required fields are marked *