The HP 6205B Operating and Service Manual provides detailed instructions for setting up and operating the dual-range DC power supply, which includes features such as remote programming, series and parallel operations, and auto-tracking capabilities. It also covers troubleshooting procedures, specifications, and options for enhancing the power supply's functionality, such as overvoltage protection and voltage control adjustments.
Overview
The DC Power Supply, Model 6205B, is a fully transistorized unit suitable for bench or relay rack operations. It consists of two independently controlled dual range sections, each capable of providing either a 0-40 Volt output at 300mA or a 0-20 Volt output at 600mA. The power supply features front panel meters and controls, remote programming, remote sensing, series and parallel operation modes, and auto-tracking capabilities. It is designed for regulated constant voltage/current limiting and is protected from overloads. The manual covers the specifications, options, and accessories available for the power supply, as well as instructions for ordering additional manuals.
Specifications
- INPUT: 115Vac ±10%, single phase, 48-440Hz.
- OUTPUT: Two independent outputs, each of which can be set at either 0-40 Volts @ 0.3 Amp or 0-20 Volts @ 0.6 Amp.
- LOAD REGULATION: Less than 0.01% plus 4mV for a full load to no load change in output current.
- LINE REGULATION: Less than 0.01% plus 4mV for any line voltage change within the input rating.
- RIPPLE AND NOISE: Less than 200µVrms 1mV p-p.
- TEMPERATURE RANGES: Operating: 0 to 50°C, Storage: -40 to +75°C.
- TEMPERATURE COEFFICIENT: Less than 0.02% plus 1mV per degree Centigrade.
- STABILITY: Less than 0.10% plus 5mV total drift for 8 hours after an initial warm-up time of 30 minutes at constant ambient, constant line voltage, and constant load.
- INTERNAL IMPEDANCE AS A CONSTANT VOLTAGE SOURCE: Less than 0.02 ohms from dc to 1kHz. Less than 0.5 ohms from 1kHz to 100kHz. Less than 3.0 ohms from 100kHz to 1MHz.
- TRANSIENT RECOVERY TIME:
- OUTPUT CONTROLS: RANGE switches select desired operating mode for each section and coarse and fine VOLTAGE controls set desired output voltages.
- OUTPUT TERMINALS: Six "five-way" output posts (three for each section of supply) are provided on the front panel and two output terminal strips (one per section) are located on the rear of the chassis. All power supply output terminals are isolated from the chassis and either the positive or negative terminals may be connected to the chassis through separate ground terminals located on the output terminal strips.
- ERROR SENSING: Error sensing is normally accomplished at the front terminals if the load is attached to the front or at the rear terminals if the load is attached to the rear terminals. Also, provisions are included on the rear terminal strips for remote sensing.
- REMOTE RESISTANCE PROGRAMMING: 200 ohms per Volt.
- REMOTE VOLTAGE PROGRAMMING: 1 Volt per Volt.
- COOLING: Convection cooling is employed. The supply has no moving parts.
- SIZE:
Controls & Indicators
The front panel of the DC Power Supply Model 6205B includes meters and operating controls for each section. Each section has a RANGE switch to select the operating mode (either 40V or 20V) and VOLTAGE controls to adjust the output voltage continuously within the selected range. The METER switch on the front panel allows for measuring either output voltage or output current in one of two ranges.
Installation / Setup
Refer to the PDF for details.
Operation
Refer to the PDF for details.
Troubleshooting & Error Codes
Refer to the PDF for details.
Safety & Warnings
Refer to the PDF for details.
Download SERVICE Service manual (PDF – 715.9 KB)
HP 6205B Service Manual PDF: Aids technicians in troubleshooting and calibrating the HP 6205B model. File size: 715.9 KB.
- Brand: Hp-6205b-operating
- Model: SERVICE
- Type: Service manual
- File size: 715.9 KB
Overview
Brief overview of the product.
Specifications
- Key spec 1
- Key spec 2
Controls & Indicators
Control panel/button layout.
Installation / Setup
- Step 1…
- Step 2…
Operation
Basic usage, modes, cycles.
Troubleshooting & Error Codes
| Issue / Code | Fix |
|---|---|
| Example | How to fix… |
Safety & Warnings
- Important warning…
Downloads
Download SERVICE service manual (PDF)