Wire the Receiver Box

Find a suitable location near to the boiler, leaving at least 30cm distance from any metal objects including metal wall boxes and boiler housing.

Honeywell T4R Wireless Programmable Thermostat - Box
A) Wall box or Rear
Wiring Hinge opens the terminal block flap to access the cables and wall box screw holes.
B) Surface
Wiring Use the cable clamps to secure the surface wiring.
Honeywell T4R Wireless Programmable Thermostat - Box 1
C) Replace the cover
Locate the hinges at the top of the cover and wall plate, close the cover and secure with the screw.
Honeywell T4R Wireless Programmable Thermostat - Boiler

Warning iconTo prevent a short circuit from a loose wire 

  • When using multi-core cables: Only remove enough outer insulation to allow secure fixing of the cores into the terminal block.
  • When using single-core cables: Secure them together with a cable tie as close as possible to the terminal block.

Power Up and TestHoneywell T4R Wireless Programmable Thermostat - Test

Honeywell T4R Wireless Programmable Thermostat - Receiver Box

A) Power Up the Thermostat
Remove the battery tab and clip the thermostat onto the table stand or wall bracket. Find a suitable location for the thermostat away from draughts, direct sunlight, or other heat sources.
B) In the Power Up Menu that appears, by pressing + and –  select your language and adjust the year, month, day, time, and the number of periods.
C) Power Up the Heating System and Receiver Box and do a quick functional test of the receiver box to check that it switches the boiler.

Configure the SystemHoneywell T4R Wireless Programmable Thermostat - System

Specific settings for the thermostat and heating system can be configured in the advanced menu.
Press and holdmenu and then buttons together until the display changes (approx. 3sec).

A) Press√ andfunction buttons to navigate through the parameter listB) Press+ and- buttons to change a parameter
C) Press√ the button to save the change (or pressfunction to cancel the change)D) Pressindoor use only. the button to exit the advanced menu and save any changes

To rebind the thermostat and receiver box
The thermostat and receiver box in this pack are pre-bound. Follow these instructions only if a binding is required.
To enter the binding menu press and holdmenu and then buttons together until the display changes (approx. 3sec), and follow steps A) to C) above to navigate the binding parameters. Keep at least 1m between devices during binding.

NoDescriptionSettings (default in bold)
Honeywell T4R Wireless Programmable Thermostat - icon 19RF Binding Mode0, 1 = Enter bind mode
Honeywell T4R Wireless Programmable Thermostat - icon 20RF Signal Strength Test0, 1 = Perform Signal Test
Honeywell T4R Wireless Programmable Thermostat - icon 21Delete RF Binding Data0, 1 = Delete Bind Data
Honeywell T4R Wireless Programmable Thermostat - ORANGE

A) Clear the binding data from the Receiver Box:
Press & hold the reset ‘pinhole’ button for 3sec.
B) Put the Receiver Box into bind mode:
Hold button for 3sec – button lights ORANGE for 3sec followed byHoneywell T4R Wireless Programmable Thermostat - OFF 1 LED flashing ORANGE.
C) Clear the binding data from the Thermostat:
Change parameter No 14 C (Delete RF Binding Data) to ‘1’ and press
D) Put the Thermostat into bind mode:
Change parameter No 14 A (RF Binding Mode) to ‘1’ and press
If successful the Receiver BoxHoneywell T4R Wireless Programmable Thermostat - OFF 1 LED will turn solid  GREEN and the Thermostat will showHoneywell T4R Wireless Programmable Thermostat - OFF 1

Parameters

Description I- Settings (default in bold)
Honeywell T4R Wireless Programmable Thermostat - icon 4Language1= EN
Honeywell T4R Wireless Programmable Thermostat - icon 5Heating Cycle Rate (cps)3 (oil boiler / thermal actuator)
6 (gas or combi boiler / zone valve) 9 12
Honeywell T4R Wireless Programmable Thermostat - icon 6Minimum on time1- 5 (mins) (set to 4 mins for oil boiler)
Honeywell T4R Wireless Programmable Thermostat - icon 7Lower Temperature Limit5 – 21 (°C)
Honeywell T4R Wireless Programmable Thermostat - icon 8Upper-Temperature Limit21 – 35 (°C)
Honeywell T4R Wireless Programmable Thermostat - icon 9Schedule options1= 7 days (different schedule each day of the week)
2 = 5 + 2 day (weekday + weekend schedule)
3 = 1 day (same schedule every day)
Honeywell T4R Wireless Programmable Thermostat - icon 10Number of periods per day4 or 6
Honeywell T4R Wireless Programmable Thermostat - icon 11Fail Safe mode0 = Boiler off, 1 = Boiler 20% on / 80% off
Honeywell T4R Wireless Programmable Thermostat - icon 12Backlight0 = Off, 1 = On (only on demand)
Honeywell T4R Wireless Programmable Thermostat - icon 13Clock Format0 = 24 hr, 1 = AM/PM
Honeywell T4R Wireless Programmable Thermostat - icon 14Daylight Saving time change0 = Off, 1 = Auto
Honeywell T4R Wireless Programmable Thermostat - icon 15Temperature Display Offset+/-3°C
Honeywell T4R Wireless Programmable Thermostat - icon 16Restore Schedule Defaults0, 1 = reset
Honeywell T4R Wireless Programmable Thermostat - icon 17Restore Factory Settings0, 1 = reset
Honeywell T4R Wireless Programmable Thermostat - icon 18Optimisation0 = Disabled, 1= Enabled

Troubleshooting

What’s happening?What it could mean…How to fix it…
The thermostat display is blankBatteries exhausted installed incorrectly or the tab hasn’t been removedPull thermostat from wall bracket or table stand and check battery installation –  replace batteries if necessary
Display =Honeywell T4R Wireless Programmable Thermostat - icon 2Battery power is critically lowPull thermostat from wall bracket or table stand and check battery installation – replace batteries if necessary
Display =Honeywell T4R Wireless Programmable Thermostat - icon 3Faulty temperature sensorReplace thermostat or check the wiring to remote temperature sensor if fitted
The thermostat shows heat demand but the boiler doesn’t respondBoiler (water) already t temperatureNormal behavior – wait for the water temperature to drop
Faulty wiring connectionCheck wiring at thermostat and boiler terminals
Thermostat display shows and Receiver Box Honeywell T4R Wireless Programmable Thermostat - LEDLED is flashing REDWireless communication with Receiver Box is lostMove thermostat to a location where wireless communication is reliable
Thermostat display shows and Receiver Honeywell T4R Wireless Programmable Thermostat - OFF Box LED is OFFThermostat and Receiver Box not boundFollow the Wireless Binding Instructions
Receiver BoxHoneywell T4R Wireless Programmable Thermostat - OFF 1 LED is flashing ORANGEReceiver Box is in bind modeWait for bind mode to time out (3min) or bind a Thermostat
Honeywell T4R Wireless Programmable Thermostat - icon

Hereby, Pittway Sarl declares that the radio equipment type T4H700RF2053 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity
is available at the following internet address: https://hwllhome.co/DoC

ErP: Class V (+3%), (EU) 811/2013
Receiver Category 2
Frequency Band: 868–868.6MHz (868.3MHz)
Max Power: 25mW

Dustbin

WEEE Directive 2012/19/EC
Waste Electrical and Electronic Equipment directive At the end of the product life dispose of the packaging and product in a corresponding recycling center. Do not dispose of the unit with the usual domestic refuse. Do not burn the product.

Honeywell T4R Wireless Programmable Thermostat - icon 1
Honeywell T4R Wireless Programmable Thermostat - logo 1

www,resideo.com
Pittway Sarl, Z.A. La Pièce 4,
1180 Rolle, Switzerland
Country of origin: UK

© 2020 Resideo Technologies, Inc. All rights reserved.
The Honeywell Home trademark is used under license from Honeywell International Inc.
This product is manufactured by Resideo Technologies, Inc. and its affiliates.

Documents / Resources

Honeywell T4R Wireless Programmable Thermostat [pdf] Installation Guide
T4R Wireless Programmable Thermostat, T4R, Wireless Programmable Thermostat

References

Leave a comment

Your email address will not be published. Required fields are marked *