Packing List

After unpacking, check for any signs of damage. Report any damage to your supplier immediately. Also check whether all items are present:

  • ADPRO® eFT Series
  • Power cord
  • CD with client software and manuals
  • Quick Setup Guide
  • 19″ mounting brackets (for eFT-T4 variant).
  • Set of 4 rubber feet to use the device as a desktop unit.
  • 4 SATA cables for eFT-T4 or 2 SATA cables for eFT-T2.
  • Network patch cable
  • Screws set
  • USB mouse
    The products are provided with a plug according to the National Heavy Current Regulations of the country of shipment. Installation shall be done according to National Regulations.
Honeywell ADPRO FastTrace 2 Series Hybrid--Repeat for 

Note
Wherever eFT Series device or XO device is mentioned in this document, it refers to all models of the eFT Series unless specifically mentioned otherwise.

Power Requirements

The XO device is designed for 100–240 V~, 50/60 Hz operation. XO devices comply with EMF emission and immunity standards. The eFT-T2 variant has a 12 V DC input external adapter.

Honeywell ADPRO FastTrace 2 Series Hybrid--Repeat

Caution!
Do not connect XO devices to electrical outlets or circuits shared with other devices that draw significant startup currents, or cause significant electrical interference, such as air conditioners or photocopiers.

Safety Instructions

The plug is used as power inlet for the XO device. The outlet socket must be installed near the XO device and must be easily accessible. This equipment is not suitable for use in locations where children are likely to be present.

Technical Documents

Download the eFT Series Hardware Installation Manual (35450) and XO Client Software User Manual (21796) from our website www.xtralissecurity.com.  You can also download technical data sheets on specific devices that connect to the XO device.

You can find the latest versions of this document and any referenced document on the Security Solutions Support site www.xtralissecurity.com (logon may be required). If a document number is indicated (between parentheses), you can enter it in the Keywords box on the site, and search for the document.

Installing the XO Client Software on Your PC

System Requirements for the Client PC
Hardware

The following are the recommended hardware requirements to run the XO client on a PC:

  • Intel Core i5 processor with 8GB RAM
  • Graphics card with DirectX 12 support and the capability for using YUV surfaces and hardware stretching. Intel® HD Graphics 630 is recommended.

The rendering switches to the GDI mode when the graphics card does not have this support. Rendering in GDI mode is not recommended because of high CPU utilization.
The embedded client application is now by default a 64-bit application, and the customers who require a 32-bit version can download it from the support site.

Honeywell ADPRO FastTrace 2 Series Hybrid--Repeat

Caution!
HD cameras can be used more optimally in a PC with better system specifications. Please take into account that double resolution, on average, results in 4 times more performance. Honeywell advises testing the settings to make sure that your PC can handle your configuration.

Software

The following are the recommended software requirements to run the XO client on a PC:

  • Windows 10 (64-bit)
  • DirectX 12 drivers
  • Internet Explorer 11
Honeywell ADPRO FastTrace 2 Series Hybrid--Repeat for 

Note
Firmware with hardware version 2.0.0.0 and software version 1.0.0.1 is needed to decode firmware in the older devices still running the HIPI card hardware. 
It is strongly recommended to download the latest drivers for your video card from the site of the manufacturer of your card. Doing this will resolve a number of issues that you would probably encounter.

  • NVIDIA: www.nvidia.com
  • ATI/AMD: http://ati.amd.com
    The client can be forced to use GDI mode. Just put gdi=1 in the [General] section of the hydra.ini file located in your data directory. The default location is:
    c:\users\<username>\AppData\Roaming\Hydra\hydra.ini.
Installing the XO Client Software

This document describes how to install the XO client via the XO device’s web page. For this, you need to add the device’s web page to the trusted sites in Internet Explorer. Furthermore, your PC must have an IP address in the same network range as the XO device.
You can also install the XO client using the stand-alone client installer. This requires an internet connection for downloading. For instructions, see the XO Client Software User Manual (21796).

Honeywell ADPRO FastTrace 2 Series Hybrid--Repeat for 

Note
The webserver is disabled by default starting with ADPROXO 5.0. It can only be reenabled by a technician on a system in which an admin user has enabled the technical grant. To install the client software using the XO device’s web page, the webserver must be enabled by the technician which is a security risk. You can get the client software from the release DVD or from the support site (www.xtralissecurity.com).

Internet Explorer Settings
Honeywell ADPRO FastTrace 2 Series Hybrid--Repeat for 

Note
The preferred browser for installing the XO client software is Internet Explorer. If you cannot use Internet Explorer, try any other internet browser. In this case, you have to install the MeadCo Neptune plugin. You can download the plugin from www.meadco.com/Neptune/Download.

When installing the XO client software via the XO device’s web page, you need to add the XO device’s IP address to your Trusted sites in Internet Explorer. The XO device’s default IP address is 10.0.0.10 with subnet mask 255.255.255.0. Proceed as follows:

  1. In Internet Explorer, choose Tools > Internet options.
  2. Click the Security tab.
  3. In the Select a zone… box, click Trusted sites, and then click Sites.
  4. In the Add this website… box, type http://followed by the XO device’s IP address. For example: http://10.0.0.10
  5. Click Add, and then click Close.
  6. Click OK to close the Internet Options window.
    If installation is still not possible, you may try clearing the Enable Protected Mode checkbox in the Security tab.
Honeywell ADPRO FastTrace 2 Series Hybrid--Repeat for 

Caution!
Check with the IT department if you are allowed to switch off protected mode, because it may lead to  IT issues.

Changing the PC’s IP Address

The XO device’s default IP address is 10.0.0.10 with subnet mask 255.255.255.0. If you install the client software via the device’s web page, or if you want to configure a device using the XO client, you need to put your PC in the same IP range (for example, IP address 10.0.0.2 with subnet mask 255.255.255.0).

To change the PC’s IP address in Windows 10, proceed as follows:

  1. Click Start, and then click Control Panel (View by: Category).
  2. Click Network and Internet.
  3. Click Network and Sharing Center.
  4. Click Connections.
  5. Click Properties.
  6. Click Internet Protocol Version 4 (TCP/IPv4).
  7. For ease of initial setup, change the PC’s TCP/IP settings to the following:
    IP address10.0.0.2Subnet mask255.255.255.0
  8. Click OK to return to the Local Area Connection window.
  9. Click OK to close the window.
Honeywell ADPRO FastTrace 2 Series Hybrid--Repeat for 

Note
You can check the XO device information by running the following commands when you are connected to the device with a monitor and keyboard.

ALT + F1To display the IP details
ALT + F7To display the cameras in matrix layout
Installation
Honeywell ADPRO FastTrace 2 Series Hybrid--Repeat for 

Note
Webserver is disabled by default starting with ADPRO XO 5.0. It can only be reenabled by a technician on a system in which an admin user has enabled the technical grant. To install the client software using the XO device’s web page, the webserver must be enabled by the technician which is a security risk. You can get the client software from the release DVD or from the support site (www.xtralissecurity.com).

To install the XO client software via the XO device’s web page, proceed as follows:

  1. Connect your PC to the XO device’s eth0 port with an RJ45 network cross cable or via the network switch/router on the eth0 port.
    Honeywell ADPRO FastTrace 2 Series Hybrid-- Connect your PC
  2. Open Internet Explorer and enter the XO device’s IP address, followed by /setup.php For example:http://10.0.0.10/setup.php
    Honeywell ADPRO FastTrace 2 Series Hybrid-- Open Internet Explorer 
  3. Click setup.exe.
    Honeywell ADPRO FastTrace 2 Series Hybrid--o set up how th
  4. Click Run to start the installation.
    Note
    Your virus scanner may block this download. Disable your virus scanner temporarily if this occurs. Remember to switch it back on after installation.
  5. The following warning message may appear:
    Do you want to allow the following program from an unknown publisher to make changes to this computer? In this case, click Yes to start the installation.
  6. Click Yes in the following message. This message is displayed as changing the default password for XO device from first login is made mandatory since XO 04.05.005.
    Honeywell ADPRO FastTrace 2 Series Hybrid-- Click Yes in the following message
  7. Click OK to uninstall the previous XO client.
    Honeywell ADPRO FastTrace 2 Series Hybrid-- Click OK to uninstall
  8. Click Uninstall to confirm. When finished, the following screen appears:
    Honeywell ADPRO FastTrace 2 Series Hybrid-- Click Uninstall to confirm
  9. Click Finish. The new version will now install.
    Honeywell ADPRO FastTrace 2 Series Hybrid-- Click Finish
  10. Click I Agree to agree with the terms of the license agreement.
    Honeywell ADPRO FastTrace 2 Series Hybrid--Click I Agree to agree
  11. Accept or modify the installation folder. Click Next.
    Honeywell ADPRO FastTrace 2 Series Hybrid-- CAccept or modify
  12. Accept or modify the default work folder (= the folder for storing snapshots and downloaded recordings). Also select your preferred language. Click Install, and wait for the following screen to appear:
    Honeywell ADPRO FastTrace 2 Series Hybrid-- ccept or modify
  13. When the installation is completed, click Close to exit the installation Wizard. The new client version is now installed.
    Honeywell ADPRO FastTrace 2 Series Hybrid-- When the installation

Launching the XO Client

To launch the XO client, proceed as follows:

  1. On the desktop, double-click the XO client icon Honeywell ADPRO FastTrace 2 Series Hybrid-- Launch the XO client--555
    If the icon is not available, you can press Start and choose All Programs > ADPRO XO > AdproXO. The following window appears:
    Honeywell ADPRO FastTrace 2 Series Hybrid-On the desktopThe Login window displays all your XO devices so that you can quickly connect to them.
  2. To set up how the client launches, click Settings.
    Honeywell ADPRO FastTrace 2 Series Hybrid--o set up how the client
  3. Provide the following information:
ItemDescription
English, FrancaisSelect the desired language for the application.
GUI styleSelect a style to change the appearance of the application. The changes will only take effect after you restart the client software.
PathIf required, change the default work folder (= the folder for storing snapshots and downloaded recordings).
Use hardware
acceleration if available
Select this option if you want to use hardware decoding on your client PC. Hardware decoding may enhance the rendering performance.
Save live viewSet this option to Yes if you want to show the last used camera matrix in the live view. If you set it to No, the live view window is empty when you start the client, and you have to select the cameras for the live view matrix each time you start the client.
Auto restartSet this option to Yes if you want the login window to reappear when you close the client software. This allows you to quickly connect to another XO device.

4.  Click OK to save the settings.
5. If you have changed the GUI style, close the Login window, and then restart the client application for the changes to take effect.
You can now add an XO device and connect to it.

Adding an XO Device to the XO Client

To add an XO device to the client, proceed as follows:

  1. Launch the XO client.
    Honeywell ADPRO FastTrace 2 Series Hybrid-On the desktop
Honeywell ADPRO FastTrace 2 Series Hybrid--Repeat for 

Note
If you have installed the XO client for the first time on this PC, you can add a few demo devices  to familiarise yourself with the XO client before adding your own device(s). Access to the demo devices is limited; not all features are available. Once you have added your own device(s) to the client, you can no longer add the demo devices.

Honeywell ADPRO FastTrace 2 Series Hybrid--Click Add

2. If you want to add the demo devices, click Demo sites. Continue with the next step to add your own devices.
3. Click Add. The following window appears:
4. Provide the following information:

ItemDescription
NameType a meaningful name for the XO device.
IP AddressType the IP address or DNS hostname of the XO device (default IP address is 10.0.0.10).
RTSP Port Control PortType the RTSP port number (default is 554) and the control port number (default is 2000).
HTTPS PortThe HTTPS port number (default is 443)
Select the Use encrypted streaming checkbox for secure video streaming.
Note:
Restart the XO device after the secure streaming is enabled. Encryption is applied only on the input video stream and not on the input audio stream.
The Honeywell Miracle cameras will not support audio-out functionality when encrypted streaming is used.
P2P License UIDEnter the UID for P2P connection same as that of the XO server and select Use P2P.
Enable P2P on the XO server from System > Connections > Ethernet / PPP > P2P configure for this field to display on the client login page. For more details, see Network (Ethernet).
Connection TypeSelect the TCP or UDP protocol. UDP is recommended, but TCP may be required if the connection goes through a router that blocks the UDP packets.
Username PasswordEnter the user ID/username and password of an existing user to log on to the XO device. The default user ID is 0. The XO device has 666777 as the initial password which is changed at the first login.
Note
• Entering a password is optional. If you leave the Password box blank, you have to fill in the password manually each time you connect to the device.
Honeywell ADPRO FastTrace 2 Series Hybrid--Repeat for any other

5. Click OK. The new XO device appears in the list.
6. Repeat for any other XO devices that you want to add.

Connecting to an XO Device

To connect to an XO device, proceed as follows:

  1. Launch the XO client. The list of XO devices appears. The system automatically selects the last used XO device.
    Honeywell ADPRO FastTrace 2 Series Hybrid--Repeat for any other
  2. Click the desired XO device in the list, and then click Connect.
    Alternatively, double-click the desired XO device in the list. The Live Video screen appears:
    Honeywell ADPRO FastTrace 2 Series Hybrid-- Click the desired XO
Honeywell ADPRO FastTrace 2 Series Hybrid--Repeat for 

Note
If you did not specify a password for connecting to the device, the following screen appears:

Honeywell ADPRO FastTrace 2 Series Hybrid-- Note

Enter the password and click Login.

www.security.honeywell.com

A Disclaimer about this document, statements about Intellectual Property, Copyright, and Liability, as well as a General Warning are available in an earlier section of this document.

Document No: 35447_01
P/N 19531912

Honeywell ADPRO FastTrace 2 Series Hybrid--logo

Documents / Resources

Honeywell ADPRO eFT Series Remotely Programmable NVR+ Network Video Recorders [pdf] User Guide
ADPRO eFT Series, Remotely Programmable NVR Network Video Recorders, Network Video Recorders, Remotely Programmable NVR

References

Leave a comment

Your email address will not be published. Required fields are marked *