COMPONENTS

  1. Front Grille
  2. Spinner
  3. Blades
  4. Plastic Nut
  5. Rear Grille
  6. Motor Shaft
  7. Speed Knob
  8. Oscillating Clutch Knob
  9. Motor Housing
  10. Tilt Adjustment Knob
  11. Power Supply Cord with Plug
  12. Base

ASSEMBLY INSTRUCTIONS

Assembly of Blade and Guards

  1. Unscrew the spinner clockwise and the nut counter-clockwise to separate them (Steps 1, 2, and 3 – Fig. 1).
  2. Set the rearguard in the proper position with handle up.
  3. Screw on plastic nut tightly to attach rear grille.
  4. Discard plastic sleeve on the motor shaft. Install the blade onto the shaft until it reaches the retaining pin (Steps 4, and 5 – Fig. 2).
  5. Screw spinner onto motor shaft counterclockwise to blade.
  6. Press the front grille onto the rear grille until the front grille is properly fitted, fix both grilles with rim and use a screwdriver to tighten the locking screw.
  7. Secure both grilles firmly by tightening the fan grille locking screws and nuts (Fig. 3).

OPERATING INSTRUCTIONS

Speed Knob
The speed of the fan is controlled by rotating the speed knob. The number on the knob will indicate which of the two speeds is in effect:
0 = Off; 1 = Low; 2 = High.

Oscillation
To make the fan oscillate, press down on the oscillating control knob located on the top of the motor housing. To stop oscillation, pull up on the knob.

Tilt Adjusting
To adjust the airflow upward or downward, loosen the screw, gently push the grilles (1,5) to the desired position and retighten the screw.

CLEANING AND STORAGE

Cleaning

  1. Unplug the fan from the electricity supply.
  2. Only use a soft cloth to gently wipe the fan clean.
  3. DO NOT immerse the fan in water and never allow water to drip into the motor housing.
  4. DO NOT use petrol, paint thinner, or other chemicals to clean the fan.
  5. Dismantling for cleaning the fan is not recommended. Use a vacuum cleaner with a brush attachment to clean the grilles, followed by a soft damp cloth.
Storage

For storage, clean the fan carefully as instructed and store your fan in a cool dry place.

Honeywell 2 Speed Oscillating Table Fan - Disposal icon

Disposal:
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.

CONDITION OF PURCHASE
As a condition of purchase the purchaser assumes responsibility for the correct use and care of this KAZ product according to these user instructions.

WARNING: IF PROBLEMS ARISE WITH THIS KAZ PRODUCT, PLEASE OBSERVE THE INSTRUCTIONS IN THE WARRANTY CONDITIONS. DO NOT ATTEMPT TO OPEN OR REPAIR THE KAZ PRODUCT YOURSELF, AS THIS COULD LEAD TO TERMINATION OF THE WARRANTY AND CAUSE DAMAGE TO PERSONS AND PROPERTY.
Technical modifications reserved.

KAZ Europe SA,
Place Chauderon 18 (9th floor)
CH – 1003 Lausanne
Switzerland
Tel. +41 21 644 01 10
www.kaz-europe.com

Honeywell 2 Speed Oscillating Table Fan - logo

The Honeywell trademark is used by Kaz, Inc. under license
from Honeywell Intellectual Properties, Inc.
www.kaz-europe.com
HT-109E-OM//0//2007-01-09 31IM109E190
1/9/07 4:44:44 PM

Documents / Resources

Honeywell 2 Speed Oscillating Table Fan [pdf] Instruction Manual
2 Speed Oscillating Table Fan, HT-109E, 28W

Leave a comment

Your email address will not be published.