Heathkit AT-1 Assembly Operation Manual (3) (PDF)

The Heathkit Model AT-1 Transmitter manual provides detailed instructions for assembly, operation, and troubleshooting, including how to set up the transmitter for different amateur radio bands using crystal or VFO control. It also covers adjustments for optimal performance, such as tuning the antenna coupler and monitoring current levels to ensure proper resonance and avoid over-coupling.

  • Brand: Heathkit
  • Model: AT-1
  • Type: operation manual
  • File size: 3.0 MB

Manual Overview

The Heathkit Model AT-1 Transmitter manual provides detailed instructions for operation, troubleshooting, and adjustments. The transmitter is designed for use on amateur bands from 80 to 10 meters, utilizing either crystal or VFO control. For troubleshooting, the manual emphasizes the importance of quickly tuning the OUTPUT control to achieve resonance, as excessive current draw can occur if circuits are not properly tuned. Error diagnostics involve monitoring the grid and plate current using a three-position meter switch, which helps identify issues with resonance and coupling. Calibration involves adjusting the antenna coupler and OUTPUT control to ensure proper current levels, typically around 60 to 80 milliamperes for optimal operation. The manual also provides board-level guidance, detailing the use of specific tubes like the 5U4G rectifier, 6AG7 oscillator, and 6L6 amplifier-doubler, and highlights the importance of using the correct crystal frequencies to avoid operating near band edges. Proper setup and adjustments ensure reliable performance and minimize interference.

Quick Issues Covered

  • Diagnose power-up failures with standby and power switches.
  • Calibrate using meter switch for grid and plate current readings.
  • Use schematics for circuit tracing and component layout.

Overview

The Heathkit Model AT-1 Transmitter is designed for both novice and experienced amateur radio operators. It is a versatile kit that can be constructed easily and used as a low-power phone transmitter or an all-band exciter for a high-power final. The transmitter supports crystal or VFO control and covers amateur bands of 80, 40, 20, 15, 11, and 10 meters. It includes features to minimize TV interference and uses proven tube types and circuitry for reliable service. The manual covers assembly, operation, and adjustments for different bands, ensuring proper tuning and operation.

Specifications

  • RF Amplifier Power Input 25-30 Watts
  • Output Connection 52 Ohm Coaxial Cable
  • Oscillator Operation Crystal, can be operated by a VFO
  • Amplifier Operation CW, can be modulated for phone
  • Band Coverage 80, 40, 20, 15, 11, 10 Meters
  • Tube Complement
  • 5U4G Rectifier
  • 6AG7 Oscillator – Multiplier
  • 6L6 Amplifier – Doubler
  • Power Requirements 105-125 50/60 Cycle, 100 Watts
  • Cabinet Size 8 1/8" high x 13 1/8" wide x 7" deep
  • Net Weight 13 Ibs.

Operation

The Heathkit Model AT-1 Transmitter can be operated on amateur bands of 80, 40, 20, 15, 11, and 10 meters using crystal or VFO control. For operation, the operator should determine the frequency range of the desired band and permissible emission type. The transmitter allows for crystal operation and can also be controlled by a VFO by plugging the VFO output into the crystal socket.

For 80 meter operation, plug in a crystal with a frequency between 3,500 and 4,000 kc, turn on the power switch, and allow the transmitter to warm up. With the STANDBY switch in the STANDBY position, turn the meter switch to PLATE, then turn on the STANDBY switch, depress the key, and quickly tune the OUTPUT control for a dip. Adjust the antenna coupler for a rise in plate current, continuously adjusting the OUTPUT control for resonance. The final current reading should be about 60 to 80 milliamperes.

For 40 meter operation, plug in a crystal between 3,500 and 3,650 kc, turn the meter switch to GRID, turn the STANDBY switch on, depress the key, and quickly tune the DRIVER control for maximum meter reading. Then, turn the meter switch to PLATE, depress the key, and tune for a dip. Tune the antenna as outlined for 80 meter operation.

For 20, 15, 11, and 10 meter operation, use the same tuning method as for the 40 meter band, with appropriate crystal frequencies. The 15 and 11 meter bands are operated on the 10 meter position of the band switch.

Download PDF (3.0 MB)

Leave a Comment