Hammarlund HX-50 Instruction Service Manual (PDF)

The Hammarlund HX-50 Transmitter/Exciter manual provides detailed instructions for setup, operation, and troubleshooting, including the requirements for immediate operation, such as a 40-80 ohm terminated antenna system and a 115-volt AC power source. It also covers installation guidelines, such as avoiding warm or drafty locations, and includes information on rear panel connections for microphones, keys, and antennas, as well as troubleshooting tips for preventing television interference.

  • Brand: Hammarlund
  • Model: HX-50
  • Type: service manual
  • File size: 2.0 MB

Manual Overview

The Hammarlund HX-50 Transmitter/Exciter manual provides detailed guidance on troubleshooting, diagnostics, and adjustments. For troubleshooting, the manual emphasizes the importance of ensuring correct connections and checking for any physical damage upon unpacking. It advises verifying the power source compatibility to prevent extensive damage. The manual does not specify error codes but suggests checking connections and components if issues arise. Calibration involves using the built-in quartz crystal sideband filter and ensuring the output matches the desired frequency bands, with specific attention to the 10-meter band segments for accuracy. Board-level guidance includes using the rear panel connections for integrating the transmitter with other equipment, such as microphones and antennas. The manual highlights the use of specific connectors for optimal performance and advises on the proper setup of the station control terminal board to facilitate seamless operation. The HX-50 is designed with TVI suppression features, including a pi-network for harmonic suppression, ensuring minimal interference with television signals.

Quick Issues Covered

  • Diagnose power-up failures with 115V AC source check.
  • Adjust C.T.O. for less than 5 Kc/s error in calibration.
  • Use schematics for circuit tracing and troubleshooting.

Overview

The Hammarlund Model HX-50 Transmitter/Exciter is designed for SSB, AM, and CW transmission across various amateur radio bands. It can function as a standalone transmitter or as an exciter for a linear power amplifier. The device requires a 40-80 ohm terminated antenna system, a key or microphone, and a 115-volt AC power source for operation. The manual covers its features, installation, and connections, emphasizing its design to suppress television interference and detailing the necessary setup for optimal performance.

Specifications

  • Stable quartz crystal sideband filter – operating at approximately 3 Mc/s.
  • Built-in antenna change over relay.
  • Time sequenced, automatic break-in CW keying (VOX keying).
  • C.T.O. direct reading to 10 Kc/s points with less than 5 Ke/s error between adjacent 100 Ke/s calibration points after calibrating.
  • 90 Watts plate input to the final amplifier on SSB, and CW.
  • Six band output 80, 40, 20, 15, and 10 meter bands supplied; 160 meter band output available on special order; 10 meter band coverage in three individually calibrated switched segments provide the same calibration accuracy as lower frequency bands.

Installation / Setup

The installation highlights for the Hammarlund Model HX-50 Transmitter/Exciter include the following:

1. Unpacking: After unpacking, inspect the unit for any transit damage and file a claim with the carrier if necessary. Check all shipping labels and tags for special instructions before discarding them.

2. Location: Avoid placing the unit near heat sources or in drafty areas. Ensure there is adequate space around the unit for air circulation.

3. Power Source: The unit operates on 105-125 Volts, 50-60 Cycle AC power and consumes 250 Watts. Verify the power source with the local power company if unsure to avoid damage.

4. Rear Panel Connections:
– Microphone Receptacle: Use a high impedance communications microphone with an Amphenol type 75-MCIF connector.
– Key Jack: A standard two-conductor phone jack for hand key or “bug” operation.
– RF Output Connector: Connect to the antenna system or a linear amplifier using a 50-70 ohm coaxial cable with an Amphenol type 83-1SP (PL-259) connector.
– Receiver Antenna Connector: Connects the antenna system to the receiver through a phono type coaxial connector.
– Station Control Terminal Board: An eight terminal screw type board for integrating the unit into the station control system, with specific terminals for accessory relay contacts, receiver output, and speaker connections.

These setup instructions ensure proper installation and operation of the HX-50 Transmitter/Exciter.

Download PDF (2.0 MB)

Leave a Comment