Hallicrafters SR-2000 Operation and Service Instruction Manual (PDF)

The Hallicrafters Model SR-2000 Transceiver manual provides detailed instructions for setup, operation, and troubleshooting, including wiring and component changes, control settings, and tuning procedures. It also includes technical specifications, such as tube and diode complement, frequency control, and power supply requirements, to ensure optimal performance and prevent issues like television interference.

  • Brand: Hallicrafters
  • Model: SR-2000
  • Type: service manual
  • File size: 8.6 MB

Manual Overview

The Hallicrafters Model SR-2000 Transceiver service manual emphasizes troubleshooting, calibration, and adjustments for optimal performance. Technicians are advised to replace the original schematic diagram and parts list with updated versions provided in the errata sheet. Key adjustments include modifying the PLATE control setting for a 50-ohm load at 7.0 MC from 3 to 7. Calibration procedures involve setting the BAND SELECTOR at 7.0, the OPERATION control at REC, and the VFO at 7250 KC. Technicians should use a low-level RF signal generator to tune the PRESELECTOR control for maximum audio output and adjust the 6.25 MC trap coil for minimum output. The manual includes detailed board-level guidance, specifying tube and diode functions, and provides error diagnostics through comprehensive metering for the final amplifier tubes. The transceiver features a noise blanker circuit, VOX/PTT control options, and a crystal lattice filter for selectivity, ensuring stable and precise operation across amateur bands.

Quick Issues Covered

  • Adjust PLATE control for 50-ohm load at 7.0 MC.
  • Calibrate VFO using built-in 100 KC crystal calibrator.
  • Refer to updated schematic for wiring/component changes.

Overview

The Hallicrafters Model SR-2000 Transceiver is a precision-built, compact, high-performance transceiver designed for amateur radio use. It operates on the 80, 40, 20, 15, and 10 meter amateur bands and supports single sideband (SSB) and continuous wave (CW) code signals. The transceiver features an Amplified Automatic Level Control (AALC) to prevent signal splatter, a noise blanker circuit, and a Receiver Incremental Tuning (RIT) control for fine-tuning. It includes 19 tubes, one voltage regulator, and 22 diodes, and can operate at the maximum legal power limit with the Model P-2000 Power Supply. The design also incorporates measures to suppress television interference and offers various operational controls and features for enhanced performance and user convenience.

Specifications

  • Tuning Ranges: Full frequency coverage of the amateur bands in eight ranges
  • Heterodyne Oscillator Crystals: Type CR-18A4/U in HC-6 holder
  • Types of Emission: SSB – Selectable USB/LSB with suppressed carrier, CW – Keyed RF carrier
  • Frequency Control: Self-contained VFO for transmit and receive modes
  • Transmission Control: Single Sideband Operation, MOX – Manual (Push-to-talk), VOX – Voice control, CW Operation, MOX – Manual, VOX – Automatic break-in
  • Frequency Stability: Less than 250 cycles drift in first hour, after a fifteen minute warm-up, and less than 100 cycles per hour thereafter
  • Tube and Diode Complement: 19 tubes plus one voltage regulator and 22 diodes
  • Cable Connector Data: Front Panel, MIC connector – Amphenol type 80-MC2M, PHONES jack – Standard 1/4-inch two conductor phone plug, Rear Cabinet, KEY jack – Standard 1/4-inch two conductor phone plug, ANTENNA connector – Mil. No. PL-259 (49190) UHF series, RCVR AUDIO (500 OHMS) connector – Standard RCA phono plug, POWER connector – Cinch-Jones type S-312-CCTL (12-pin plug), HI-VOLTAGE connector – Cinch-Jones type S-2402-CCT (2-pin plug), ACCESSORY connector – Amphenol type 86-PM11 (11-pin plug)
  • Power Supply Requirements: Model P-2000

Download PDF (8.6 MB)

Leave a Comment