Drake FS-4 Instruction Manual and Schematics (PDF)

The manual for the Drake FS-4 frequency synthesizer provides detailed instructions on installation, operation, and troubleshooting for use with Drake's "4" line equipment, including the R4, T-4X, and SPR-4 series. It covers the setup process, including power requirements and connection instructions, operational guidance with front panel controls, and maintenance procedures, ensuring proper performance and addressing potential issues.

  • Brand: Drake
  • Model: FS-4
  • Type: manual
  • File size: 3.0 MB

Manual Overview

The Drake FS-4 Frequency Synthesizer manual provides detailed guidance for technicians on installation, operation, and maintenance. The FS-4 is designed to work with Drake’s “4” line equipment, offering continuous frequency coverage without additional crystals. It connects via an accessory crystal socket and supplies injection signals in 0.5 MHz steps from 11.1 to 40.6 MHz. For installation, ensure the FS-4 is placed away from heat sources and connected to the correct power supply, with specific instructions for 120 VAC and 240 VAC operations. During operation, the front panel controls allow frequency adjustments in 10 MHz, 1 MHz, and 0.5 MHz increments, with the 0.5 MHz knob also serving as the power switch. Proper connection of the injection cable is crucial for optimal performance, and the manual advises on band selection and preselector settings. Maintenance involves alignment instructions and troubleshooting guidance, emphasizing correct use to prevent damage. The manual also includes warranty information, highlighting the importance of proper maintenance and repair to ensure product longevity.

Quick Issues Covered

  • Diagnose power-up failures with FS-4 frequency synthesizer.
  • Identify and resolve calibration errors in frequency display.
  • Trace circuits using detailed FS-4 schematics.

Overview

The FS-4 is a frequency synthesizer designed for use with the Drake Company’s “4” line equipment, such as the R4 series, T-4X series, and SPR-4. It connects to an unused auxiliary crystal socket in the receiver or transmitter, providing various injection signals and allowing continuous coverage without the need for accessory crystals. The FS-4 displays the received frequency band, which, when combined with the receiver’s “PTO” readout, gives the correct received frequency. It supplies crystal oscillator injection signals in 0.5 MHz steps from 11.1 to 40.6 MHz. An accessory kit is available for the SPR-4 receiver, and a special kit is necessary for use with the 2-C receiver. The manual includes five chapters covering introduction, installation, operation, theory of operation, and maintenance.

Specifications

MODEL FS=44

Controls & Indicators

All controls and displays necessary for the operation of the FS-4 are located on the front panel. The three knobs switch the frequency range in 0.5 MHz steps and provide direct frequency display in MHz at the readout directly above each knob. These knobs switch the frequency in steps of 10 MHz, 1 MHz, and 0.5 MHz from left to right. The 0.5 MHz knob also turns the FS-4 on and off.

Installation / Setup

The FS-4 should be placed on either side of the receiver/transmitter, not on top of the transmitter, due to heat and airflow considerations. It comes with a 20-inch cable for connection to the accessory crystal socket. The unit is factory-wired for 120 VAC, but can be adjusted for 240 VAC by altering connections at the transformer. The power line is fused for 120 VAC with a 3AG Type 1/8 A, Slo-Blo fuse, and for 240 VAC with a 3AG Type 1/16 A fuse.

Operation

The FS-4 frequency synthesizer is operated using controls and displays located on its front panel. It features three knobs that switch the frequency range in 0.5 MHz steps and provide a direct frequency display in MHz. These knobs adjust the frequency in steps of 10 MHz, 1 MHz, and 0.5 MHz from left to right, with the 0.5 MHz knob also serving as the power switch for the device.

To connect the FS-4, an injection cable is used to link it to an unused accessory crystal socket on the receiver or transmitter. The ground lug should be attached to the chassis at the accessory crystal socket, and the center pin should be inserted into the selected socket. Optimal operation is achieved when the center conductor is connected to the emitter of the crystal oscillator.

When controlling a receiver or transmitter with the FS-4, the receiver/transmitter must be set to the appropriate band, and the crystal switch should be placed in the position corresponding to the FS-4’s connection. The RF tune (preselector) must be adjusted as in normal use.

A stick-on decal is provided for easy positioning of the RF tune (preselector) on the receiver/transmitter front panel. Proper use of the FS-4 with transmitters requires caution, and users should consult RF Tune calibration charts in the T4X series manual.

To tune a receiver with the FS-4, the following steps are recommended:
a. Set the FS-4 to the desired operating frequency, such as 7.0 for the 40-meter amateur band.
b. Place the R-4 Receiver “Xtals” switch in the position corresponding to the FS-4’s connection.
c. Set the R4 “Band” switch to the appropriate band, such as 7.0.
d. Adjust the “PRESELECTOR” control to the correct setting, for example, between 5 and 6.

Download PDF (3.0 MB)

Leave a Comment