BK Precision 1670A Instruction Manual (PDF)

The manual for the B+K Precision Model 1670A Triple Output DC Power Supply provides detailed instructions on setup, operation, and safety precautions, including how to connect and operate the power supply, set voltage and current limits, and troubleshoot issues such as overloads. It also includes specifications for the power supply's outputs, maintenance guidelines, and information on fuse replacement and repair services.

  • Brand: BK Precision
  • Model: 1670A
  • Type: manual
  • File size: 565.3 KB

Manual Overview

The B+K Precision Model 1670A is a triple output DC power supply designed for versatile use, offering both constant voltage and constant current regulation. It features variable outputs ranging from 0 to 30 volts and 0 to 3 amps, with additional fixed outputs at 5 volts and 12 volts, each capable of delivering up to 0.5 amps. The unit is equipped with digital LCD meters for monitoring voltage and current with resolutions of 0.1 volts and 0.01 amps, respectively. The power supply is fully overload protected and can operate continuously at its maximum rated output. For troubleshooting, the manual emphasizes the importance of safety precautions, particularly when dealing with high voltage equipment. It advises using an isolation transformer and discharging capacitors to prevent shock hazards. The manual also provides guidance on connecting outputs in series and replacing fuses. The Model 1670A’s design includes features such as short circuit protection, thermal overload protection, and reverse polarity protection to ensure safe and reliable operation.

Quick Issues Covered

  • Diagnose power-up failures with voltage/current output checks.
  • Identify error codes for constant voltage/current mode issues.
  • Calibrate voltage/current using digital LCD meter readings.

Overview

The B+K Precision Model 1670A is a general-purpose triple output DC power supply. It provides versatile constant voltage or constant current regulated power, variable from 0 to 30 volts and 0 to 3 amps. The power supply includes fixed 5 volt and 12 volt outputs, each capable of providing up to 0.5 amps. It is designed to power circuit boards during troubleshooting and can provide up to three outputs simultaneously, with each output fully isolated for positive or negative polarity. The manual covers safety precautions, specifications, controls and indicators, operating instructions, maintenance, and service information to ensure maximum performance and longevity of the power supply.

Specifications

  • Variable 0-30 VDC
  • 0 to 3 Amps
  • Binding Posts
  • 3 digit LCD
  • 0.1 V
  • + (1% reading + 2 digit)
  • <0.05% + 10 mV
  • <0.05% + 10 mV
  • <5 mVrms
  • Fixed 12 VDC 45%
  • Fixed 5 VDC 45%
  • 0 to 500 mA continuous
  • Wire clips
  • <1%
  • < 1%
  • =5 mV rms
  • Variable speed thermal static control fan
  • 4.9" x 8.5" x 9.5" (124 x 216 x 242mm)
  • 115/230 VAC, 50/60 Hz
  • 165W
  • 0° TO 40° C, 10-80%R.H.
  • -15° TO 70° C, S 85% R.H.
  • – 10-80% R.H.
  • – Altitude up to 2000m
  • – Installation category: CAT II
  • – Pollution degree: 2
  • – Mains supply voltage fluctuation up to +10% of normal voltage

Controls & Indicators

The source does not provide complete information about the front-panel controls/indicators for the Model 1670A.

Safety & Warnings

Normal use of test equipment can expose users to electrical shock hazards, especially when testing in areas with exposed high voltage. An electrical shock with a current of 10 milliamps passing through the heart can be fatal. Voltages as low as 35 volts DC or AC RMS are considered dangerous as they can produce lethal currents under certain conditions. Users should adopt safe work habits to avoid contact with high voltage and to prevent current from passing through the heart in case of accidental contact. Specific safety precautions include:

1. The DC output of the power supply poses little shock risk, but certain test conditions can create high voltage hazards:
a. A “hot chassis” type equipment under test poses a serious shock hazard unless unplugged or isolated with a transformer.
b. If the equipment under test is powered and uses high voltage, the power supply outputs may float to high potentials. Do not float the output more than 100 volts peak relative to ground.
c. Discharge high-voltage capacitors in equipment under test before making connections or tests, as some circuits retain high voltage even when off.

2. Use a polarized 3-wire AC outlet to ensure the power supply is grounded, reducing shock risk.

3. Avoid unnecessary exposure to high voltage. Remove covers only when needed, turn off equipment when making high-voltage connections, and discharge capacitors after removing power.

Download PDF (565.3 KB)

Leave a Comment