The service manual for the B&K Precision Model 360 V-O-Matic covers detailed operating instructions, including setup procedures for measuring various ranges of voltage, current, and resistance, as well as guidelines for using the range selector and polarity reversal switch to ensure accurate readings. It also provides troubleshooting tips, such as ensuring the pointer reads zero before use and using the anti-parallax mirror for precise measurements, while emphasizing safety precautions like turning off power when connecting or disconnecting test leads.
Manual Overview
The B&K Precision Model 360 V-O-Matic is an automatic volt-ohm-milliammeter designed for precise measurements across various electrical parameters. The service manual emphasizes the importance of proper calibration and adjustment before usage, including zeroing the pointer using the zero adjust screw. Troubleshooting involves ensuring the range selector switch is correctly detented to avoid misreadings. The manual provides detailed guidance on handling different voltage ranges, advising starting measurements at the highest range when the voltage is unknown and adjusting downward for accuracy. For D.C. voltage measurements, the polarity reversal switch is crucial for correct readings, and specific instructions are given for high-voltage scenarios up to 6,000 volts. The manual outlines the use of an anti-parallax mirror to enhance reading accuracy. Error codes or diagnostics are not explicitly mentioned, but the manual stresses careful handling of test leads and the meter during high-voltage measurements to prevent damage or inaccurate readings. Calibration and adjustments are integral to maintaining the instrument’s accuracy, with precision resistors ensuring long-term stability.
Quick Issues Covered
- Diagnose power-up failures by checking battery and connections.
- Calibrate using zero adjust screw for accurate readings.
- Use schematics for circuit tracing and fault isolation.
Overview
The Model 360 V-O-Matic is an automatic volt-ohm-milliammeter produced by B&K Manufacturing Company, a division of Dynascan Corporation. It features a single scale for direct reading, eliminating errors from incorrect scale reading. The device includes an anti-parallax mirror for accuracy, precision resistors for stability, and a range switch coupled to the meter dial. It measures D.C. and A.C. voltages, direct current, resistance, capacity, and power, with specific ranges and sensitivities detailed in the specifications. The manual provides operating instructions, including safety precautions and measurement techniques.
Specifications
- D.C. Volts: 250 millivolts full scale, 3 volts full scale, 15 volts full scale, 60 volts full scale, 300 volts full scale, 1000 volts full scale, 6000 volts full scale
- A.C. Volts: 3 volts full scale, 15 volts full scale, 60 volts full scale, 300 volts full scale, 1000 volts full scale, 6000 volts full scale
- D.C. Sensitivity: 20,000 ohms per volts
- A.C. Sensitivity: 5,000 ohms per volts
- A.C. Frequency Response: 5 cycles to 0.5 me.
- A.C. Output Meter Ranges: 0-3 volts, 0-15 volts, 0-60 volts, 0-300 volts
- D.C. Blocking Capacitor on output range: .1 mfd, 600 volts
- Direct Current: 0-100 microamperes, 0-5 milliamperes, 0-100 milliamperes, 0-500 milliamperes, 0-10 amperes
- Resistance Ranges: 1,000 ohms full scale, 10 ohms center scale; 10,000 ohms full scale, 50 ohms center scale; 1M ohms full scale, 4K ohms center scale; 100M ohms full scale, 150K ohms center scale
- Accuracy: Plus or minus (+) 3% of full scale on D.C. Ranges, Plus or minus (+) 5% of full scale on A.C. Ranges, Resistance Accurate to +2 degrees of arc
- Capacity: Direct reading with the overlay scales in three ranges 1 mfd to 4.1 mfd, .0025 mfd to .12 mfd, 100 mmfd to 4500 mmfd
- Db Ranges: From —20 Db to + 62 Db, 0 Db is equal to 1 milliwatt into a 600 ohm line
- Power: Direct reading with the overlay scales for A.C. sine wave power across 4, 8 and 16 ohm loads; Across 4 ohm load 0-56 watts, 8 ohm load 0-28 watts, 16 ohm load 0-56 watts
- Peak to Peak (P-P) Voltages: Direct reading with the overlay scales, 0-170 P-P, 0-850 P-P
- Battery: 1 each #2 Flashlight Cell 1.5 volt, 1 each 2U6 or equivalent 9 volts
- Size: 814" x 6" x 374”
- Weight: 4 Ibs.
Operation
The operation and basic usage steps for the Model 360 V-O-Matic include setting the Range Selector switch to the desired range, starting at the highest range if unsure of the voltage to be measured. The Polarity Reversal switch should be set to the (+) position, and the V-O-Matic 360 should be connected to the circuit under test. If the meter reads backwards, the Polarity Reversal switch should be rotated to the (—) position. For voltages over 1,000 volts and less than 6,000 volts, the red test lead should be connected to the 6,000 volts D.C. jack and the black test lead to the (—) jack, with the Range Selector switch set to the 60 volts D.C. position. When making measurements on the 6,000 volts range, power should be turned off to the circuit under test before connecting and disconnecting the V-O-Matic 360, and the test leads or the V-O-Matic should not be touched when power is applied. The meter should be read using the anti-parallax mirror for accuracy, ensuring the pointer and its reflection coincide.