BK Precision 262 Instruction Manual (PDF)

The manual for the Model 262 Tone Generator & Cable Tracer Kit provides detailed instructions for setting up and operating the device, including changing the frequencies produced by the tone generator and using the cable tracer to identify wires. It also covers troubleshooting steps, such as checking line polarity and replacing the battery, and includes warranty information for repairs and service.

  • Brand: BK Precision
  • Model: 262
  • Type: manual
  • File size: 177.8 KB

Manual Overview

The B&K Precision Model 262 Tone Generator & Cable Tracer Kit manual provides detailed instructions for troubleshooting, calibration, and adjustments. To change the frequencies produced by the Tone Generator, users must access the internal jumpers by removing the case and disconnecting the battery. The jumper settings, detailed in the manual, allow selection of specific frequencies. Troubleshooting involves checking LED indicators for continuity and polarity, with specific modes for testing phone line polarity and providing talk current on dead lines. The Cable Tracer operates by tracing the probe over wires, with sound intensity indicating proximity to the signal. For battery replacement, users should carefully disassemble the case, replace the battery, and reassemble the unit. Warranty and service information specify procedures for repair or replacement, emphasizing the need for proof of purchase and adherence to shipping guidelines. The manual stresses careful handling to avoid voiding the warranty through misuse or unauthorized modifications.

Quick Issues Covered

  • Diagnose tone generator frequency issues using jumper settings.
  • Identify cable tracer faults with speaker tone detection.
  • Access circuit board for schematic tracing and adjustments.

Overview

The Model 262 Tone Generator & Cable Tracer Kit is a hand-held, battery-powered instrument designed for testing telephone lines and identifying wires without piercing insulation. The Tone Generator can connect to stripped wires, terminal panels, wall plates, or modular jacks using alligator clips and an RJ11 plug. It generates a warbled tone and can check phone line polarity, provide talk current on a dead line, and has selectable test frequencies. The Cable Tracer is capable of identifying tones up to 12 inches away and can trace signals through various non-metal surfaces under ideal conditions. Both devices are powered by a standard 9-volt battery.

Specifications

  • Tone Generator Specifications
  • Tone Output Level: Approximately 8 vp-p (+3dBm, 600Q)
  • Tone Output Current: Approximately 4mA
  • Tone Frequency:
  • J1 Jumper J2 Jumper Tone Frequency Switching Frequency
  • J1 connected J2 connected 1.4KHz to 1KHz 14Hz
  • J1 disconnected J2 connected 0.84KHz to 0.7KHz 14Hz
  • J1 connected J2 disconnected 1.4KHz to 1KHz 7Hz
  • J1 disconnected J2 disconnected 0.84KHz to 0.7KHz 7Hz
  • Continuity / Talk Test: 35mA (leads shorted), approximately 6.5 VDC (leads open)
  • Dimensions (H x W x D): 7" x 1.87" x 1.12" (177.8 x 47.5 x 28.4 mm)
  • Weight: 5.8 oz. (164.4 g)
  • Power: Standard 9-volt battery
  • Cable Tracer Specifications
  • Dimensions (H x W x D): 7.37" x 1.87"x 1.12" (187.1 x 47.5 x 28.4 mm)
  • Weight: 4.9 oz. (138.9 g)
  • Power: Standard 9-volt battery

Operation

The Model 262 Tone Generator & Cable Tracer Kit operates in several modes. The Tone Generator has three modes: OFF/POLARITY, TONE, and CONTINUITY/TALK. In the OFF/POLARITY mode, the unit is powered off but can test phone line polarity, indicated by an LED. In the TONE mode, the unit generates a selected tone on all three lines. In the CONTINUITY/TALK mode, it applies approximately 6.5 VDC to the red wire and checks for continuity, lighting an LED if continuity exists, and provides talk power on a dead line.

The Cable Tracer operates by pressing a push button and tracing the probe tip over wires. If a wire carries the Tone Generator’s frequencies, the tones will be audible from the Cable Tracer’s speaker, with volume increasing as the probe gets closer to the wire.

Download PDF (177.8 KB)

Leave a Comment