BK Precision 230A Instruction Manual (PDF)

The BK Precision 230A Multi-Network Cable Tester manual provides instructions for setting up and operating the device, including testing various types of cables such as Ethernet, 10-Base-T, and Token Ring, using an auto-scanning feature to check for continuity, miswiring, and polarization. It also offers troubleshooting tips, such as ensuring a 9-volt battery is installed and advising against connecting the tester to a live circuit to avoid damage.

  • Brand: BK Precision
  • Model: 230A
  • Type: manual
  • File size: 171.1 KB

Manual Overview

The BK Precision 230A Multi-Network Cable Tester is designed to quickly assess cable integrity by auto-scanning for continuity, miswiring, and polarization issues across various cable types, including Ethernet, 10-Base-T, and Token Ring. For troubleshooting, the device uses LED indicators to signal cable status. A green LED indicates a good cable, while a red or unlit LED suggests a fault. For coaxial cables, the BNC LED should remain unlit unless a test is in progress. For other cables, LEDs on the remote terminator scan each pair; green indicates proper connection, while red or no light indicates a problem. Calibration involves ensuring a 9-volt battery is installed and the GND switch is off unless testing shielding. The manual cautions against connecting the tester to live circuits to prevent damage. Warranty service requires proof of purchase and covers defects for one year, excluding misuse or unauthorized repairs.

Quick Issues Covered

  • Diagnose cable faults using LED indicators for quick results.
  • Identify miswiring and polarization errors in network cables.
  • Refer to schematics for circuit tracing and troubleshooting.

Overview

The 230A Multi-Network Cable Tester by BK Precision is designed to quickly test cables for continuity, miswiring, and polarization across various network types, including thin Ethernet (BNC/TNC), 10-Base-T (UTP/STP), AT & T 258A, TIA 568A/B, Token Ring, and USOC4/6/8 modular cables. The manual covers the use of the tester with an attached remote terminator for testing cables both before and after installation, providing easy access and quick checks.

Installation / Setup

The setup for the 230A Multi-Network Cable Tester involves ensuring a 9-volt alkaline battery is installed in the battery compartment. When testing coaxial cables, one end should be plugged into the BNC socket of the master unit and the other end into the remote terminator. For 10-Base-T, AT & T 258A, EIA/TIA 568, and Token Ring cables, one end should be connected to the jack of the master unit and the other to the remote terminator. The power switch must be turned on, and the power LED should flash to indicate proper operation. It is important to keep the GND switch off unless testing the shielding. The device should not be connected to a live circuit to avoid damage.

Operation

The 230A Multi-Network Cable Tester is used to quickly test cables for continuity, miswiring, and polarization. It supports various cable types including thin Ethernet (BNC/TNC), 10-Base-T (UTP/STP), AT & T 258A, TIA 568A/B, Token Ring, and USOC4/6/8 modular cables. The tester can be used with an attached remote terminator to test cables both before and after installation. For coaxial cables, one end is plugged into the BNC socket of the master unit and the other into the remote terminator. The power switch is turned on, and the power LED should flash. If the BNC LED lights up, the cable is bad. For other cable types, one end is plugged into the master unit and the other into the remote terminator. The power LED should flash, and the remote terminator LEDs will scan. If the LEDs light green, the cable is good. If they light red or do not light, the cable is bad. For shielded cables, the GND switch can be used to test the shielding.

Safety & Warnings

Please make sure a 9-volt alkaline battery has been installed in the battery compartment. Remember to always keep the GND switch off if you are not testing the shielding. Do not connect the cable tester to a live circuit, as the unit may be damaged by over voltage.

Download PDF (171.1 KB)

Leave a Comment