The manual provides instructions for installing and operating HP DC module connectors, detailing the process of making load connections, setting the sense switch for local or remote voltage sensing, and attaching the connector to the mainframe. It also includes troubleshooting tips such as clipping jumpers for relay board installation and ensuring screws are tightened correctly without overtightening.
Manual Overview
The installation guide for Agilent Technologies DC Module Connectors provides detailed instructions for setting up both standard and relay connectors. The guide emphasizes the importance of proper wiring and securing connections using the provided barrier block, which accepts spade, ring terminals, or stripped wires. It is crucial to hand-tighten screws evenly to avoid damage. The guide outlines the process for making load connections, which are consistent across both connector types, and highlights the use of a five-terminal barrier block for wire connections. For relay connectors, additional steps include clipping eight jumpers on the connector board before installing the relay board. The sense switch must be set to Local unless remote sensing is required. The guide advises careful handling when attaching connectors to the mainframe, ensuring all screws are started before tightening. The document also provides instructions for upgrading a standard connector to a relay connector by clipping specific jumpers and installing a relay board. Proper labeling of the connector post-installation is recommended to indicate the presence of a relay board.
Quick Issues Covered
- Diagnose power-up failures with local/remote sense switch settings.
- Resolve load connection errors with barrier block wiring instructions.
- Calibrate voltage sensing using relay board installation guidelines.
Overview
The document is an installation guide for Agilent Technologies DC Module Connectors, specifically the Standard Connector (P/N 5060-3386) and the Relay Connector (P/N 5060-3387). It provides instructions on making load connections, attaching connectors to the mainframe, and setting the sense switch for local or remote voltage sensing. The guide also covers upgrading a standard connector to a relay connector by installing a relay board.
Specifications
- +Sense used to connect the + remote sense lead.
- —Sense used to connect the — remote sense lead.
- GND used for signal ground (GND) connections.
- +Output used to connect the + output load wire.
- -Output used to connect the — output load wire.
- Five-terminal barrier block provided for wire connections.
- Barrier block screws are 6-32 x 1/4 inch.
- Sense switch to select either local or remote voltage sensing.
- Relay connectors include load and sense disconnect and polarity reversal relays.
Controls & Indicators
Refer to the PDF for details.
Installation / Setup
The installation guide for Agilent Technologies DC Module Connectors highlights several key points for setup. Load connections are made on the connector supplied with each module, which is fastened to the back of the mainframe. This allows modules to be installed or removed without disturbing the wiring. The connector has a switch to select either local or remote voltage sensing. For wiring, loosen the barrier block screws and connect the wires using spade or ring terminals, or a stripped wire. Secure the wires with a tie-wrap. When closing the connector, tighten screws evenly and avoid overtightening. Attach the connector to the mainframe at the appropriate slot location and tighten the screws. If upgrading to a relay connector, clip the jumpers on the connector board before installing the relay board. Set the sense switch to Local unless remote sensing is required.
Operation
The manual provides instructions on how to connect and install Agilent Technologies DC module connectors. It describes the process of making load connections using a five-terminal barrier block, which accepts spade, ring terminals, or stripped wires. The connector has a switch to select between local or remote voltage sensing. It also outlines steps for opening, connecting wires, and closing the connector, emphasizing not to overtighten screws. Additionally, it explains how to upgrade a standard connector to a relay connector by clipping jumpers and installing a relay board.
Troubleshooting & Error Codes
Refer to the PDF for details.
Safety & Warnings
The manual includes the following safety warnings and precautions:
– Hand tighten screws only.
– Start all screws before tightening.
– Tighten screws evenly.
– Do not overtighten screws.
– Do not use locking-type adhesives on the screws.
Download INSTALLATION Manual (PDF – 70.8 KB)
Installation guide for HP-DC-Module-Connectors, detailing step-by-step procedures for proper setup and connection.
- Brand: Hp-dc-module-connectors
- Model: INSTALLATION
- Type: Manual
- File size: 70.8 KB
Overview
Brief overview of the product.
Specifications
- Key spec 1
- Key spec 2
Controls & Indicators
Control panel/button layout.
Installation / Setup
- Step 1…
- Step 2…
Operation
Basic usage, modes, cycles.
Troubleshooting & Error Codes
| Issue / Code | Fix |
|---|---|
| Example | How to fix… |
Safety & Warnings
- Important warning…
Downloads
Download INSTALLATION manual (PDF)